LSI Network Card 7202CP User Manual

USER’S  
GUIDE  
LSI7202CP CompactPCI  
Dual Channel  
2 Gbit/s Fibre Channel  
Host Adapter  
F e b r u a r y 2 0 0 2  
Version 1.0  
®
DB15-000228-00  
 
This document contains proprietary information of LSI Logic Corporation. The  
information contained herein is not to be used by or disclosed to third parties  
without the express written permission of an officer of LSI Logic Corporation.  
LSI Logic products are not intended for use in life-support appliances, devices,  
or systems. Use of any LSI Logic product in such applications without written  
consent of the appropriate LSI Logic officer is prohibited.  
The host adapter(s) referred to in this User's Guide contain one or more  
transceivers that are certified as Class 1 laser products that conform to the  
requirements contained in the US Food and Drug Administration - Center for  
Devices and Radiological Health (FDA/CDRH) regulation 21 CFR 1040,  
Performance Standards for Light-Emitting Products and 21 CFR 1010,  
Performance Standards for Electronic Products: General.  
Internationally, these transceivers are certified as Class 1 laser products that  
conform to the requirements contained in the International Electrotechnical  
Commission (IEC) standard 825-1 (1993). Class 1 laser products are not  
considered to be hazardous based upon current medical knowledge. This class  
includes all lasers or laser systems which cannot emit levels of optical radiation  
above the exposure limits for the eye under any exposure conditions inherent in  
the design of the laser product. The design of the transceivers on this host  
adapter is such that access to laser radiation above a Class 1 emission level  
during operation, user maintenance, or service conditions is prevented. However,  
there may be a laser embedded in the enclosure of the Class 1 laser that is more  
hazardous, but harmful radiation cannot escape the intact enclosure. With any  
laser, the following precautions should be followed to prevent accidental exposure  
to any levels of optical radiation.  
CAUTION: Do not look into the transceiver ports, do not view the transceiver  
ports with optical instruments, and avoid direct exposure to the beam.  
The following certification information is permanently affixed to or inscribed on  
the transceiver product so as to be legible and readily accessible to view when  
the transceiver is fully assembled for use.  
Laser Manufacturer  
Model #  
Serial #  
iii  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Document DB15-000228-00, Second Printing (February 2002). This document  
describes the LSI Logic LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre  
Channel Host Adapter and will remain the official reference source for all  
revisions/releases of this product until rescinded by an update.  
LSI Logic Corporation reserves the right to make changes to any products herein  
at any time without notice. LSI Logic does not assume any responsibility or  
liability arising out of the application or use of any product described herein,  
except as expressly agreed to in writing by LSI Logic; nor does the purchase or  
use of a product from LSI Logic convey a license under any patent rights,  
copyrights, trademark rights, or any other of the intellectual property rights of  
LSI Logic or third parties.  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
TRADEMARK ACKNOWLEDGMENT  
The LSI Logic logo design and Fusion-MPT are registered trademarks of LSI  
Logic Corporation. Solaris and the Solaris logo are trademarks or registered  
trademarks of Sun Microsystems, Inc. in the US and other countries and are  
used under license. All other brand and product names may be trademarks of  
their respective companies.  
For a current list of our distributors, sales offices, and design resource  
centers, view our web page located at  
iv  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Preface  
This book is the user’s guide for the LSI Logic LSI7202CP CompactPCI  
Dual Channel 2 Gbit/s Fibre Channel Host Adapter. It includes  
instructions for installing this adapter with regard to cold and hot  
installations and provides this adapter’s specifications.  
Audience  
This document assumes that you have some familiarity with CompactPCI  
computers and related support devices. The people who benefit from this  
book are:  
Engineers and managers who are evaluating or designing the host  
adapter board for possible use in a system  
End users who are installing the host adapter board into their  
computer  
Organization  
This document has the following sections:  
Chapter 2, LSI7202CP Host Adapter Characteristics  
Chapter 3, BIOS Features  
Chapter 4, Solaris Software Requirements  
Appendix A, Glossary of Terms and Abbreviations  
LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter  
v
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Conventions Used in This Manual  
Notation  
Example  
Meaning and Use  
courier typeface  
# cfagdm  
Names of commands and the output from the commands  
are shown in courier type face and enclosed in a box.  
italic underscore  
attachment_point  
When an underscore appears in an italicized string next  
to a command, enter a user-supplied item of the type  
called for with no spaces.  
Revision Record  
Revision Date  
Remarks  
0.5  
0.6  
11/01  
12/01  
First release.  
Second Advance printing. Front matter includes laser safety statement.  
Added Section 8.  
1.0  
02/02  
Final printing. Converted to LSI Logic format. Changes throughout.  
vi  
Preface  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Contents  
Chapter 1  
Chapter 2  
Chapter 3  
Installing/Extracting the LSI7202CP Host Adapter  
1.1  
Host Adapter Installation  
1-2  
1.1.1  
1.1.2  
1.1.3  
Cold Installation Preparation  
Hot Installation Preparation  
1.2  
Extracting the LSI7202CP  
1.2.1  
1.2.2  
LSI7202CP Host Adapter Characteristics  
2.1  
General Description  
2-1  
2.1.1  
2.1.2  
2.1.3  
Features  
Hardware and Software Support  
2.2  
Technical Characteristics  
2.2.1  
2.2.2  
Bus Interfaces  
BIOS Features  
3.1  
BIOS Features  
3.1.1  
3.1.2  
3.1.3  
3.1.4  
3.1.5  
Intel BIOS  
Starting the Intel BIOS Configuration Utility  
Using the Intel BIOS Configuration Utility  
Exiting the Intel BIOS Configuration Utility  
Fcode  
3-2  
3-3  
3-5  
3-6  
3.2  
Troubleshooting  
3-14  
LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter vii  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Chapter 4  
Solaris Software Requirements  
4.1  
4.2  
Device Driver Software Requirements  
Verifying the Installation  
4-1  
4.2.1  
Using the show-devs Command  
4-2  
4.2.2  
Using the probe-scsi-all Command  
4-3  
4-4  
4.3  
itmpt Device Driver  
Appendix A  
Index  
Customer Feedback  
Figures  
Tables  
2.1  
4.1  
4.2  
LSI7202CP CompactPCI Host Adapter  
pkgadd Procedure  
Completing Floppy Disk Installation  
2.1  
2.2  
2.3  
4.1  
Hardware and Software Requirements  
Specifications  
2-2  
2-5  
Power Requirements  
Error Messages  
2-5  
4-10  
viii  
Contents  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Chapter 1  
Installing/Extracting the  
LSI7202CP Host Adapter  
CompactPCI Dual Channel 2 Gbit/s Fibre Channel host adapter. The  
main topics are:  
Section 1.1, “Host Adapter Installation,page 1-1  
Section 1.2, “Extracting the LSI7202CP,” page 1-3  
1.1 Host Adapter Installation  
This section provides a general overview of the tasks needed to perform  
either a hot or cold installation. For the exact procedures required for  
your system, refer to the operating system and system documentation.  
1.1.1 Cold Installation Preparation  
Before shutting down the operating environment and halting the system,  
ensure that all significant application activity on the server has stopped.  
To prepare the system for a cold installation, follow these steps.  
Step 1. Follow the appropriate procedures, as documented in the  
system’s service manual, to shut down and halt the system.  
Step 2. Refer to the system’s documentation for the complete power  
down procedure and location of the power switch.  
Step 3. Press the power switch on the system’s status panel to power  
down the system.  
Step 4. Verify that the system’s power LED is OFF, which indicates that  
the system is completely powered off.  
After the system has been shut down and powered off, you can  
safely install the card.  
LSI7202CP Compact PCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter 1-1  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
             
1.1.2 Hot Installation Preparation  
Refer to your system’s hardware user’s manual for complete instructions  
regarding hot installation.  
1.1.3 Installation  
Review your system’s documentation for the complete instructions before  
performing the following steps to install the LSI7202CP into your system:  
Step 1. Identify the slot number where you want to insert the adapter.  
Step 2. Refer to the system’s documentation for instructions on how to  
remove the filler panel.  
Step 3. Remove the filler panel from the slot you selected.  
Step 4. Push on the red release button and open the LSI7202CP card’s  
ejection lever before installing the card in the system.  
Step 5. Pull back the ejection lever and slide the card into the  
CompactPCI slot.  
Step 6. Apply even pressure at both corners of the card and push the  
card until it is firmly seated in the slot.  
Step 7. Push the ejection lever over the sprocket toward the card and  
into the locked position. This locks the card into the slot.  
Step 8. Use a Phillips screwdriver to tighten the captive screws inside  
the card’s ejection lever.  
Step 9. Attach the Fibre Channel cable to either Port 0 or Port 1 of the  
LSI7202CP. This completes the hardware installation.  
Important: Check your system’s documentation for any additional  
actions that may be required to configure the system soft-  
ware for the newly inserted card.  
1-2  
Installing/Extracting the LSI7202CP Host Adapter  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
     
1.2 Extracting the LSI7202CP  
The LSI7202CP is a component that you can extract from a hot-swap  
compliant system without interrupting the operation of the system. You  
can also extract the adapter if installing it in a cold environment after you  
power down the system.  
You must determine whether you want to perform a cold extraction of the  
adapter or a hot extraction. In a cold extraction, you must shut down the  
system’s operating system and power down the system before extracting  
the adapter. In a hot-swap extraction, you may be required to enter  
software commands before and after the extraction to detach the adapter  
from the system correctly.  
Note :  
The following procedures provide a general overview of the  
tasks needed to prepare for either a hot or cold extraction.  
For the specific procedures required for your system, refer  
to the documentation that shipped with your system.  
1.2.1 Cold Environment Extraction  
Before extracting your adapter, ensure that all significant application  
activity on the server has stopped. To extract the LSI7202CP, follow  
these steps.  
Step 1. Refer to the system’s documentation for the complete power  
down procedure and location of the power switch.  
Step 2. Press the power switch to power down the system.  
Step 3. Verify that the system’s power LED is OFF, which indicates that  
the system is completely powered off.  
Step 4. Extract the LSI7202CP after the system has been shut down  
and powered off.  
1.2.2 Hot Environment Extraction  
Refer to your system’s hardware user’s manual for complete instructions  
regarding hot environment extraction.  
Extracting the LSI7202CP  
1-3  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
             
1-4  
Installing/Extracting the LSI7202CP Host Adapter  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Chapter 2  
LSI7202CP  
Host Adapter  
Characteristics  
This chapter provides instructions for installing and extracting the host  
adapter board and includes these topics:  
Section 2.1, “General Description,page 2-1  
Section 2.2, “Technical Characteristics,page 2-3  
2.1 General Description  
The LSI7202CP is a CompactPCI dual channel 2 Gbit/s Fibre Channel  
host adapter. The following sections describe the features of and the  
hardware and software support for the LSI7202CP.  
2.1.1 Features  
The LSI7202CP adapter supports these features:  
Hot-swap CompactPCI/PCI installation and removal  
Asynchronous and synchronous transfers  
2.1.2 Hardware and Software Support  
The LSI7202CP supports most major software operating systems, such  
as Sun Solaris (2.6 and higher), Windows Server (NT 4.0, 2000, XP,  
.NET), Linux (RedHat, Suse, Caldera, Turbo), NetWare, UnixWare, HP-  
UX, and OS/2. The LSI7202CP host adapter utilizes the Fusion-MPT  
architecture for all major operating systems. Fusion-MPT architecture  
offers the unique feature of having a single, binary operating system  
driver that supports Fibre Channel devices and other bus architectures.  
LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter 2-1  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
                       
Before you use the LSI7202CP, make sure your system meets the  
specific hardware and software requirements as shown in Table 2.1.  
Table 2.1  
Hardware and Software Requirements  
Requirements  
Component  
For Solaris SPARC hardware environments  
Hardware  
Any Sun Microsystems computer with an avail-  
able CompactPCI slot  
Software  
Firmware  
The Solaris 8 operating environment  
OpenBoot PROM, version 2.1 or greater  
For Intel IA-32 or IA-64 hardware environments  
Hardware  
Software  
Any Intel compatible  
Windows Server (NT 4.0, 2000, XP, .NET)  
Linux (RedHat, Suse, Caldera, Turbo)  
NetWare, UnixWare, HP-UX, and OS/2  
Firmware  
Any Intel compatible BIOS system  
2.1.3 Fibre Channel Cable Assemblies  
You will use one of two types of Fibre Channel cable assemblies based  
on your system.  
LSI7202CP-LC and LSI7202CP-LC6  
LC optical to LC optical  
LC optical to SC optical  
LSI7202CP-HS and LSI7202CP-HS6  
HSSDC2 to HSSDC2  
HSSDC2 to HSSDC  
2-2  
LSI7202CP Host Adapter Characteristics  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
             
2.2 Technical Characteristics  
This section provides information about the CompactPCI, PCI, and Fibre  
Channel interfaces on the LSI7202CP. It also includes information about  
the physical, electrical, and the thermal/atmospheric characteristics of  
the LSI7202CP.  
Figure 2.1 provides a photo of the LSI7202CP.  
Figure 2.1 LSI7202CP CompactPCI Host Adapter  
Port 1 LED  
Port 0 LED  
Port 0 and Port 1  
External Fibre  
Channel Connectors  
Hot-Swap LED  
Red Release Button  
and Ejection Lever  
2.2.1 Bus Interfaces  
This section describes the bus interfaces that the LSI7202CP supports.  
2.2.1.1 CompactPCI Interface  
CompactPCI is an adaptation of the Peripheral Component interconnect  
(PCI) Specification for industrial and/or embedded applications that  
Technical Characteristics  
2-3  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
           
require a more robust mechanical form factor than desktop PCI.  
CompactPCI is electrically compatible with the PCI Specification,  
allowing low cost PCI components to be utilized in a mechanical form  
factor suited for more rugged environments. The LSI7202CP fully  
supports Hot Swap as defined in the CompactPCI Hot Swap  
Specification, Revision 1.0.  
2.2.1.2 PCI Interface  
The PCI functionality for the LSI7202CP is contained within the  
LSIFC929 Dual Channel Fibre Channel I/O Controller. This controller  
connects directly to the PCI bus and generates timing and protocol in  
compliance with PCI specifications. This interface provides a high-speed,  
standard local bus to the processor and memory subsystems in your  
computer.  
2.2.1.3 Fibre Channel Interface  
The Fibre Channel interface for the LSI7202CP is also contained within  
the LSIFC929 Dual Channel Fibre Channel I/O Controller. The LSIFC929  
controller provides a direct interface to Fibre Channel. This controller  
generates timing and protocol in compliance with the Fibre Channel  
standard.  
2-4  
LSI7202CP Host Adapter Characteristics  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
     
2.2.2 Technical Specifications  
This section contains the technical specifications for the LSI7202CP.  
2.2.2.1 Data Transfer Specifications  
Table 2.2 lists the performance specifications for the LSI7202CP.  
Table 2.2  
Specifications  
Feature  
Specification  
cPCI clock  
66 MHz max  
264 Mbytes/s  
cPCI data burst transfer rate  
2.2.2.2 Physical Characteristics  
The LSI7202CP fits the 3U Eurocard form factor of 160.00 mm x  
100.00 mm, as defined in the CompactPCI Specification, Revision 3.0.  
The component height on the top and bottom of the LSI7202CP follows  
Revision 3.0 of the CompactPCI Specification, Revision 2.2 of the PCI  
Local Bus Specification.  
2.2.2.3 Electrical Characteristics  
Table 2.3 provides the power requirements for the LSI7202CP.  
Table 2.3 Power Requirements  
Operating Voltage  
Power  
3.3 V ± 5% Operation  
50.0 mW  
7.75 W  
5.0 V ± 5% Operation  
Technical Characteristics  
2-5  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
                   
2.2.2.4 Thermal and Atmospheric Characteristics  
The following parameters define the thermal and atmospheric  
environment for the LSI7202CP during normal operation:  
Temperature range: 0 °C to 55 °C (dry bulb)  
Relative humidity range: 5% to 90% noncondensing  
Maximum dew point temperature: 32 °C  
Airflow must be sufficient to keep the LSIFC929 heat sink  
temperature below 65 °C  
The following parameters define the storage and transit environment for  
the LSI7202CP:  
Temperature range: 40 °C to +105 °C (dry bulb)  
Relative humidity range: 5% to 90% noncondensing  
2.2.2.5 Electromagnetic Compliance  
The design of the LSI7202CP minimizes electromagnetic emissions,  
susceptibility to radio frequency energy, and the effects of electrostatic  
discharge. The LSI7202CP carries the BSMI, CE mark, FCC Self-  
Certification log, Canadian Compliance Statement, VCCI, and meets the  
requirements of FCC Class A.  
2.2.2.6 Safety Characteristics  
The LSI7202CP meets or exceeds the requirements of Underwriters  
Laboratory (UL) flammability rating 94 V0. The LSI7202CP is also  
marked with the supplier’s name or trademark, type, and UL flammability  
rating.  
2-6  
LSI7202CP Host Adapter Characteristics  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
                             
Chapter 3  
BIOS Features  
This chapter provides information pertaining to Intel BIOS and Solaris  
Fcode and includes these topics:  
Section 3.1, “BIOS Features,page 3-1  
Section 3.2, “Troubleshooting,page 3-14  
3.1 BIOS Features  
A BIOS is the ROM code that is loaded by the system to facilitate booting  
from Fibre Channel drives. The BIOS also contains an embedded  
configuration manager, used to configure options provided by the  
firmware. The LSI Logic BIOS integrates with a standard system BIOS,  
extending the standard disk service routine provided through INT13h.  
Two types of BIOS are available for the LSI7202CP:  
Intel BIOS for Intel-based platforms  
Fcode for Solaris SPARC platforms.  
Both Intel BIOS and Fcode concurrently reside on the boards.  
3.1.1 Intel BIOS  
This section provides the features, description, and installation of the  
Intel Fibre Channel BIOS.  
3.1.1.1 Intel BIOS Features  
The LSI Logic FC Intel BIOS features support:  
Selection and configuration for up to 256 adapters  
LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter 3-1  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
         
Boot device selection from any four host adapters  
Automatic INT13 drive mapping for Fibre Channel drives  
3.1.1.2 BIOS Overview  
During the boot time initialization, the Intel BIOS determines if there are  
other hard disks, such as an IDE drive, already installed by the system  
BIOS. If there are, the Intel BIOS maps any Intel drives it finds after the  
drive(s) already installed. Otherwise, the Intel BIOS installs drives  
starting with the system boot drive. In this case, the system boots from  
a drive controlled by the Intel BIOS.  
3.1.1.3 Intel BIOS Boot Specification (BBS)  
The Intel BIOS provides support for the BIOS Boot Specification (BBS),  
which allows you to choose which device to boot from by selecting the  
priority.  
To use this feature, the system BIOS must also be compatible with the  
BBS. If your system supports the BBS, use the system BIOS setup menu  
to select the boot and drive order. In the system BIOS setup, the Boot  
Connection Devices menu appears with a list of available boot options.  
Use that menu to select the device and rearrange the order. Then exit to  
continue the boot process.  
3.1.2 Starting the Intel BIOS Configuration Utility  
The LSI Logic Intel BIOS allows you to change the default configuration  
of your host adapters, using the embedded BIOS Configuration Utility.  
When the BIOS loads, the following message appears on your monitor:  
Press Ctrl-C to start LSI Logic Configuration Utility...  
This message remains on your screen for about five seconds, giving you  
time to start the utility. After you press Ctrl-C, the message changes to:  
Please wait, invoking LSI Logic Configuration Utility...  
After a brief pause, your computer monitor displays the Main menu of the  
BIOS Configuration Utility.  
3-2  
BIOS Features  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
Note:  
Not all devices detected by the Configuration Utility can be  
controlled by the BIOS. Devices such as tape drives and  
scanners require that a device driver specific to that periph-  
eral be loaded. The BIOS Configuration Utility does allow  
parameters to be modified for these devices.  
3.1.3 Using the Intel BIOS Configuration Utility  
This section provides the menu formats and user inputs available to  
inform users about this utility prior to running it. All BIOS Configuration  
Utility screens that display various menus are partitioned into fixed areas.  
This area provides static general help text information.  
3.1.3.1 Main Menu  
When you invoke the LSI Logic Intel BIOS Configuration Utility, the Main  
menu appears. This screen displays a scrolling list of up to 256 host  
adapters in the system and information about each of them.  
To select an adapter, use only the arrow keys and enter key. Then, press  
Enterto view and modify the selected adapter’s properties (and to gain  
access to the attached devices). After selecting an adapter and pressing  
Enter, the FC Link bus is scanned and the Adapter Properties screen  
appears.  
On the Main menu, two selections are the Boot Adapter List and Global  
Properties menus.  
Boot Adapter List allows selection and ordering of boot adapters. Refer  
to Section 3.1.3.5, “Boot Adapter List Menu,page 3-5 for more detailed  
information.  
Global Properties allows changes to global scope settings. Refer to  
Section 3.1.3.6, “Global Properties Menu,page 3-5 for more detailed  
information.  
Only adapters with LSI Logic Control enabled can be accessed.  
3.1.3.2 Adapter Properties Menu  
The Adapter Properties menu allows you to view and modify adapter  
settings. It also provides access to an adapter's device settings. To  
BIOS Features  
3-3  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
   
display this menu, select a device under Adapter field on the Main menu  
and press Enter.  
3.1.3.3 Persistent IDs Menu  
The Persistent ID screen is used to review the automatic mapping  
between a drive WorldWide Name and its assigned logical SCSI bus and  
target ID. You can also use this screen to force a drive to a specific  
logical Target ID.  
Selecting Add WWN at an unused location clears out the associated  
WWN/DID field and allows you to enter the first 16 characters of the  
WWN. Pressing <Enter>afterwards allows the last 16 characters to be  
entered. The CU automatically adds any leading zeros if necessary. If  
you make an entry by mistake, select Erase on the appropriate line to  
remove the entry.  
Logical ID selection defaults to be the lowest ID available. This can be  
changed by using the <+> or <-> keys to cycle the numbers. The Bus  
field always defaults to 0 and cannot be changed. It is displayed in the  
case where an outside utility reserved a different number.  
Next Page and Previous Page options are provided on the persistent ID  
screens, through the F2 key, which moves the screen forward or back by  
16 entries. However, the CU requires that any modifications to the  
current page be stored before new entries may be viewed or modified. A  
confirmation window pops up asking to store or discard changes if  
needed.  
3.1.3.4 Device Properties Menu  
The Device Properties menu allows you to view and update individual  
device settings for an adapter.  
Note:  
The number of fields on the menu requires that you scroll  
left/right to view all of the information. When accessing this  
menu, use the Home/End keys to scroll to columns cur-  
rently not displayed. The scroll indicator on the bottom of  
the menu shows where the cursor is relative to the first and  
last columns.  
3-4  
BIOS Features  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
3.1.3.5 Boot Adapter List Menu  
The Boot Adapter List menu specifies the order in which adapters boot  
when more than one LSI Logic host adapter is in a system. You can  
select up to four of the total adapters in a system as bootable; however,  
you can use only one of the four “active” adapters to control a Boot  
Volume.  
To select this menu:  
1. Press F2 while on the Main menu to move the cursor to the menu  
area.  
2. Move the cursor to Boot Adapter List with the arrow keys.  
3. Press Enter.  
You can add or delete adapters using this menu. To add an adapter to  
the boot list, press the Insert key while on the Boot Adapter List. Use  
the arrow keys to select the desired adapter and press Enter to add it  
to the end of the Boot Adapter List.  
To remove an adapter from the boot list, press the Deletekey while on  
the desired adapter in the Boot Adapter List. You can also change the  
boot order by using the “+” or “” keys. For example, place the cursor on  
the adapter that you want to change, and use the “+” or “” key to raise  
or lower the boot order.  
3.1.3.6 Global Properties Menu  
The Global Properties menu allows you to pause if an alert message has  
been displayed, to view display boot information, and to set display and  
video modes.  
3.1.4 Exiting the Intel BIOS Configuration Utility  
The Exit menu for the Intel BIOS Configuration Utility is used for all five  
of the menus listed above. However, the available functionality is different  
for the Main menu and the four subordinate menus.  
BIOS Features  
3-5  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
       
To exit from the Adapter Properties, Device Properties, Boot Adapter List,  
or Global Properties menus, use these exit options:  
Cancel exit  
This option returns you to the previous menu.  
Save changes then  
exit this menu  
This option implements any changes you made on the  
previous menu and returns you to the Main menu.  
Discard changes  
then exit this menu  
This option restores the default settings and returns  
you to the Main menu.  
To exit from the Main menu, use these exit options:  
Cancel exit  
This returns you to the Main menu.  
Exit the Configuration This option exits the configuration and automatically  
Utility reboots your system.  
Important: If you reboot the system without properly exiting from this  
utility, some changes may not take effect.  
3.1.5 Fcode  
LSI Logic Solaris-capable Fusion-MPT host adapters have Fcode  
resident on board, allowing operation under Sun’s openboot console. All  
basic functionality is available at openboot, including the ability to display  
devices connected to the adapter, and boot devices on the adapter.  
3.1.5.1 Fcode Features  
The LSI Logic FC Fcode features support for:  
Solaris Sparc 2.6, 2.7, and Solaris 8 Open Firmware environments  
Root Boot device selection from any target device  
Standard command line interface, with help query  
Configuration options and selection for each host adapter  
3.1.5.2 Identifying the Fibre Channel Disks  
The probe-scsi-all command is used to identify the Fibre Channel  
devices on the Fusion-MPT adapter.  
3-6  
BIOS Features  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
To show all disks available from the openboot prompt, use the probe-  
scsi-allcommand. Note that this command is used whether the disks  
are Fibre Channel or SCSI; all disks available on all Fusion-MPT devices  
are displayed.  
ok probe-scsi-all  
/pci@8,600000/SUNW,qlc@4  
LiD HA LUN ---Port WWN--- ----Disk description----  
1 1 0 2100002037e4d65b SEAGATE ST318304FSUN18G 0726  
/pci@8,700000/IntraServer-Ultra160,scsi@3,1  
/pci@8,700000/IntraServer-Ultra160,scsi@3  
Target 0  
Unit 0 Disk IBM DDRS-34560D  
DC1B  
/pci@8,700000/IntraServer,fc@2  
MPT Version 1.00, Firmware Version 1.02.00  
Target 0  
Unit 0 Disk SEAGATE ST39173FC  
WWN 2100002037109d76 Port ID d9  
6615  
6258  
6258  
6258  
6258  
Target 1  
Unit 0 Disk SEAGATE ST39173FC  
WWN 210000203710565a Port ID 17  
Target 2  
Unit 0 Disk SEAGATE ST39173FC  
WWN 2100002037105212 Port ID 1  
Target 3  
Unit 0 Disk SEAGATE ST39173FC  
WWN 2100002037103da8 Port ID 26  
Target 4  
Unit 0 Disk SEAGATE ST39173FC  
WWN 210000203710324a Port ID 73  
/pci@8,700000/scsi@6  
Target 6  
Unit 0 Removable Read Only device PLEXTOR CD-ROM PX-20TS  
If the Fibre Channel devices on your LSI Logic adapter are not identified  
by your system, check the following:  
1. Is the Fibre Channel enclosure powered ON?  
BIOS Features  
3-7  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
2. Does the LED on the adapter indicate LINK? (note that LINK is only  
valid after the device is probed)  
3. Does the LED on the switch or remote enclosure indicate LINK?  
4. Does the LINK-SPEED parameter selected by the adapter match  
that of the bus (1G, 2G, or Auto)?  
If you do not see disks, the following additional debug information may  
help to identify the problem.  
3.1.5.3 Verifying Correct Installation  
Use this procedure to verify installation of your Fusion-MPT adapter in  
the system:  
Step 1. Power on the system.  
Step 2. When the banner displays, press the Stop-A keys to interrupt  
the boot process and stop at the ok prompt.  
Step 3. Use the show-devs command to list the system devices. You  
should see an output similar to the following:  
ok show-devs  
/SUNW,UltraSPARC-III@0,0  
/virtual-memory  
/memory@m0,0  
/aliases  
/options  
/openprom  
/chosen  
/packages  
/upa@8,480000/SUNW,ffb@0,0  
...  
/pci@8,700000/IntraServer,fc@2  
/pci@8,700000/IntraServer,fc@1,1  
/pci@8,700000/IntraServer,fc@1  
...  
/pci@8,700000/IntraServer,fc@2/disk  
/pci@8,700000/IntraServer,fc@2/tape  
/pci@8,700000/IntraServer,fc@1,1/disk  
/pci@8,700000/IntraServer,fc@1,1/tape  
/pci@8,700000/IntraServer,fc@1/disk  
/pci@8,700000/IntraServer,fc@1/tape  
/pci@8,700000/scsi@6,1/tape  
/pci@8,700000/scsi@6,1/disk  
3-8  
BIOS Features  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
ok  
/pci@8,700000/IntraServer,fc@1  
identifies the first Fibre Channel interface on an LSI Logic LSIFC929-  
based adapter  
/pci@8,700000/IntraServer,fc@1,1  
identifies the second Fibre Channel interface on an LSI Logic  
LSIFC929-based adapter  
An LSI Logic LSIFC909-based adapter shows only one such Fibre  
Channel device  
Note:  
The above are examples. The output of show-devs may  
vary depending on your system and configuration. Use the  
corresponding entries on your system, not the ones given  
here.  
If these devices are not listed, check that the adapter is correctly  
installed, and re-seat the adapter if necessary.  
3.1.5.4 Adapter-Specific Settings  
In certain circumstances, the advanced user may want to change  
settings for an individual adapter or port, without affecting the other  
adapters in the system. Specific examples of such settings are Fibre  
Channel bus speed, host adapter ID (SCSI only: Not Applicable to Fibre  
Channel), and Interrupt Coalescing.  
To select a specific Fusion-MPT adapter as the current adapter, use the  
selectcommand. Selecting a port or adapter will bring the port online,  
and will allow you to show or set certain adapter specific parameters.  
You should use caution while issuing the following commands, as certain  
commands could render the bus unusable (such as forcing 1 Gbit/s  
operation on a 2 Gbit/s Fibre Channel loop).  
select – Use the selectopenboot command to select the adapter entry.  
This will open the port to bring the port online.  
ok select /pci@8,700000/IntraServer,fc@1  
.properties – Use .properties to show the adapter properties.  
ok .properties  
BIOS Features  
3-9  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
firmware-version  
mpt-version  
scsi-initiator-id  
1.02.00  
1.00  
00 00 00 0f  
assigned-addresses 81001010 00000000 00000700 00000000 00000100  
83001014 00000000 001a0000 00000000 00020000  
8300101c 00000000 00190000 00000000 00010000  
82001030 00000000 02000000 00000000 00100000  
compatible  
model  
70 63 69 31 33 65 39 2c 36 32 31 00 70 63 69 31  
LSI,929  
reg  
00001000 00000000 00000000 00000000 00000000  
01001010 00000000 00000000 00000000 00000100  
03001014 00000000 00000000 00000000 00020000  
0300101c 00000000 00000000 00000000 00010000  
02001030 00000000 00000000 00000000 00100000  
1.00.16  
version  
device_type  
name  
scsi-2  
IntraServer,fc  
fcode-rom-offset  
66mhz-capable  
devsel-speed  
class-code  
interrupts  
latency-timer  
cache-line-size  
max-latency  
min-grant  
00000000  
00000001  
00010000  
00000001  
00000040  
00000010  
00000008  
0000001e  
00000621  
subsystem-id  
subsystem-vendor-id 000013e9  
revision-id  
device-id  
vendor-id  
00000001  
00000621  
00001000  
show-children – While you have the adapter or port selected, to display  
the devices currently connected to this adapter, use the show-children  
command:  
Select the port or adapter shown (use the port name your system  
assigns):  
ok select /pci@8,700000/IntraServer,fc@1  
ok show-children  
MPT Version 1.00, Firmware Version 1.02.00  
Link is ready, port is online  
WWN 100000a0b8040353 Port ID ef  
Target 0  
Unit 0 Disk SEAGATE ST39173FC  
WWN 2100002037109d76 Port ID d9  
6615  
6258  
6258  
Target 1  
Unit 0 Disk SEAGATE ST39173FC  
WWN 210000203710565a Port ID 17  
Target 2  
Unit 0 Disk SEAGATE ST39173FC  
3-10  
BIOS Features  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
WWN 2100002037105212 Port ID 1  
Target 3  
Unit 0 Disk SEAGATE ST39173FC  
WWN 2100002037103da8 Port ID 26  
6258  
6258  
Target 4  
Unit 0 Disk SEAGATE ST39173FC  
WWN 210000203710324a Port ID 73  
3.1.5.5 Interrupt Coalescing  
Interrupt coalescing allows the firmware on the Fusion-MPT device to  
group I/Os together to minimize the overhead to the host system. This  
feature can result in significant performance benefits when I/Os are  
rapidly coming into the adapter, as is the case while performing small  
sequential reads from a disk.  
LSI Logic has performed significant testing under multiple I/O conditions,  
and has determined that the interrupt coalescence values that are  
beneficial over a wide range of I/O conditions are a depth of 4, with a  
timeout of 160 microseconds. This means that the host is interrupted  
only once for four I/Os processed by the chip, unless 160 microseconds  
has passed since the host was last interrupted.  
Although LSI Logic has determined that these settings are optimal for a  
wide variety of situations, your own I/O load may benefit from a deeper  
queue or a longer timeout. LSI Logic provides a mechanism to modify  
these values and write them to the nonvolatile EEPROM on the adapter.  
Select the port or adapter shown (use the port name your system assigns):  
ok select /pci@8,700000/IntraServer,fc@1  
ok show-interrupt-coalescing  
Interrupt coalescing timeout is a0 (160 decimal) microseconds  
Interrupt coalescing depth is 4 (4 decimal)  
ok set-interrupt-coalescing <- command with no arguments prints help  
usage is <timeout><depth> set-interrupt-coalescing  
ok 100 8 set-interrupt-coalescing  
Interrupt coalescing timeout selected is 100 (256 decimal) microseconds  
Interrupt coalescing depth selected is 8 (8 decimal)  
BIOS Features  
3-11  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Interrupt coalescing has been set  
Change will take effect after system reset  
Note: The system must be power cycled for the changes to take  
effect. It is not sufficient to execute the reset-allcommand.  
3.1.5.6 Set Fibre Channel Link Speed  
There are two modes of operation for Fibre Channel, 1 Gbit/s and  
2 Gbit/s. It is important to match the speed of the port with the speed of  
the loop or fabric to which the port is attached.  
LSI Logic has implemented auto-negotiation on the 2 Gbit/s capable  
Fusion-MP devices. If you are experiencing difficulty with the auto  
negotiate algorithm on your fabric or loop, or you wish to manually set or  
show the link speed for the adapter, use the following procedure:  
Select the port or adapter shown (use the port name your system assigns):  
ok select /pci@8,700000/IntraServer,fc@1  
ok show-link-speed  
Link speed selected is 1 Gbaud  
Current link speed is 1 Gbaud  
ok set-link-speed <- command with no arguments prints help  
usage is <link-speed> set-link-speed  
ok a set-link-speed  
Link speed selected is autobaud  
Link speed has been set  
Change will take effect after system power cycle  
ok show-link-speed  
Link speed selected is autobaud  
Current link speed is 1 Gbaud  
Note:  
The system must be power cycled for the changes to take  
effect. It is not sufficient to execute the reset-allcommand.  
3-12  
BIOS Features  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
3.1.5.7 Persistent Device Naming  
Under certain configurations, such as when the Fibre Channel disk is the  
boot device of a system, it may be preferable to lock a target disk to a  
unit number. LSI Logic Fcode allows the system administrator to write a  
nonvolatile map of IDs to the Fibre Channel controller.  
The following is an example of how to map devices in the persistent  
device table.  
Select the controller you want to modify, as follows:  
ok show-disks  
a) /pci@1f,0/pci@1/IntraServer,fc@2/disk  
b) /pci@1f,0/pci@1/IntraServer,Ultra2-scsi@1/disk  
c) /pci@1f,0/pci@1,1/ide@3/cdrom  
d) /pci@1f,0/pci@1,1/ide@3/disk  
e) /pci@1f,0/pci@1,1/ebus@1/fdthree@14,3203f0  
q) NO SELECTION  
Enter Selection, q to quit: a  
/pci@1f,0/pci@1/IntraServer,fc@2/disk has been selected.  
Type ^Y ( Control-Y ) to insert it in the command line.  
e.g. ok nvalias mydev ^Y for creating devalias mydev for  
/pci@1f,0/pci@1/IntraServer,fc@2/disk  
ok select /pci@1f,0/pci@1/IntraServer,fc@2  
ok show-children  
MPT Firmware Version 1.00  
Target 0  
Unit 0  
Disk SEAGATE ST39173FC 6615  
WWN 200000203710c4e8 PortID a3  
ok set-persistent <- command with no arguments prints help  
usage is <current-target-id> <persistent-target-id> set-persistent  
ok 0 0 set-persistent  
ok show-persistent  
Entry 1 WWN 200000203710c4e8 Target 0  
To clear an entry in the persistent device map, use the clear-persistent  
command:  
BIOS Features  
3-13  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
ok 1 clear-persistent  
Entry 1 has been cleared  
ok show-persistent  
ok  
Entry 1 has been deleted from the table, and the table is now empty.  
3.2 Troubleshooting  
The LSI Logic Intel BIOS Configuration Utility is a powerful tool. If, while  
using it, you somehow disable all of your controllers, pressing Ctrl-Aor  
Ctrl-Eafter memory initialization during reboot allows you to re-enable  
and reconfigure.  
These messages may appear during the boot process:  
Adapter removed from boot order, parameters will be  
updated accordingly!appears when an adapter is removed from  
the system or relocated behind a PCI bridge. This message is for  
information only, and no further user action is required.  
Configuration data invalid, saving default configuration!  
appears if none of the information in NonVolatile Random Access  
Memory (NVRAM) is valid. This message is for information only, and  
can occur when the BIOS is upgraded or when some external event  
has rendered the NVRAM temporarily unreadable.  
Found FC Controller not in following Boot Order List, to  
Add: Press Ctrl-C to start LSI Logic Configuration  
Utility... appears when fewer than four adapters are in the boot  
order and adapters exist in the system which are not in the boot  
order. This message is for information only, and indicates that more  
than four adapters exist in the system. The additional adapters will  
not be managed by the Configuration Utility.  
3-14  
BIOS Features  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
Chapter 4  
Solaris Software  
Requirements  
This chapter provides device driver requirements and methods to verify  
the proper installation of the LSI7202CP, as well as installation  
instructions for the itmpt Sun SPARC Solaris driver. The chapter includes  
these topics:  
Section 4.1, “Device Driver Software Requirements,page 4-1  
Section 4.2, “Verifying the Installation,page 4-1  
Section 4.3, “itmpt Device Driver,page 4-4  
4.1 Device Driver Software Requirements  
To support the device drivers for the LSI7202CP, you must have the itmpt  
driver for your operating system installed.  
After they are installed, the boards have device paths similar to this  
example:  
/pci@8,700000/IntraServer,fc@1  
Under these nodes, one instance of the device driver that has device  
nodes is evident:  
/pci@8,700000/IntraServer,fc@1,1/disk  
/pci@8,700000/IntraServer,fc@1,1/tape  
4.2 Verifying the Installation  
To verify the proper installation of the LSI7202CP before booting the  
operating system, follow one of these two methods.  
LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter 4-1  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
         
4.2.1 nonvolatileMethod 1 – Using the show-devs Command  
Step 1. Access the ok prompt.  
Type the show-devs command:  
Step 2. The system displays output similar to this:  
ok show-devs  
/SUNW,UltraSPARC-III@0,0  
/virtual-memory  
/memory@m0,0  
/aliases  
/options  
/openprom  
/chosen  
/packages  
/upa@8,480000/SUNW,ffb@0,0  
...  
/pci@8,700000/IntraServer,fc@2  
/pci@8,700000/IntraServer,fc@1,1  
/pci@8,700000/IntraServer,fc@1  
...  
/pci@8,700000/IntraServer,fc@2/disk  
/pci@8,700000/IntraServer,fc@2/tape  
/pci@8,700000/IntraServer,fc@1,1/disk  
/pci@8,700000/IntraServer,fc@1,1/tape  
/pci@8,700000/IntraServer,fc@1/disk  
/pci@8,700000/IntraServer,fc@1/tape  
/pci@8,700000/scsi@6,1/tape  
/pci@8,700000/scsi@6,1/disk  
ok  
/pci@8,700000/IntraServer,fc@1  
identifies the first Fibre Channel interface on an LSI Logic LSIFC929-  
based adapter.  
/pci@8,700000/IntraServer,fc@1,1  
identifies the second Fibre Channel interface on an LSI Logic  
LSIFC929-based adapter  
Note:  
The above are examples. The output of show-devs may  
vary depending on your system and configuration. Use the  
corresponding entries on your system, not the ones given  
here.  
4-2  
Solaris Software Requirements  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
If these devices are not listed, check that the adapter is correctly  
installed, and re-seat the adapter if necessary.  
4.2.2 Method 2 - Using the probe-scsi-all Command  
Step 1. Access the ok prompt.  
Type the probe-scsi-all command:  
Step 2. The system then displays output similar to this:  
ok probe-scsi-all  
/pci@8,600000/SUNW,qlc@4  
LiD HA LUN ---Port WWN--- ----Disk description----  
1 1 0 2100002037e4d65b SEAGATE ST318304FSUN18G 0726  
/pci@8,700000/IntraServer-Ultra160,scsi@3,1  
/pci@8,700000/IntraServer-Ultra160,scsi@3  
Target 0  
Unit 0 Disk IBM DDRS-34560D  
DC1B  
/pci@8,700000/IntraServer,fc@2  
MPT Version 1.00, Firmware Version 1.02.00  
Target 0  
Unit 0 Disk SEAGATE ST39173FC  
WWN 2100002037109d76 Port ID d9  
6615  
6258  
6258  
6258  
6258  
Target 1  
Unit 0 Disk SEAGATE ST39173FC  
WWN 210000203710565a Port ID 17  
Target 2  
Unit 0 Disk SEAGATE ST39173FC  
WWN 2100002037105212 Port ID 1  
Target 3  
Unit 0 Disk SEAGATE ST39173FC  
WWN 2100002037103da8 Port ID 26  
Target 4  
Unit 0 Disk SEAGATE ST39173FC  
WWN 210000203710324a Port ID 73  
/pci@8,700000/scsi@6  
Target 6  
Unit 0 Removable Read Only device PLEXTOR CD-ROM PX-20TS  
Verifying the Installation  
4-3  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
If the Fibre Channel disks on your LSI Logic adapter are not identified  
by your system, check the following:  
1. Is the Fibre Channel enclosure powered ON?  
2. Does the LED on the adapter indicate LINK? (note that LINK is only  
valid after the device is probed)  
3. Does the LED on the switch or remote enclosure indicate LINK?  
4. Does the LINK-SPEED parameter selected by the adapter match  
that of the bus (1G, 2G, or Auto)?  
If you do not see disks, the following additional debug information may  
help to identify the problem.  
4.3 itmpt Device Driver  
The LSI Logic itmpt driver is designed to Sun Microsystems SCSA  
specifications for device drivers. This driver allows connection of devices  
to LSI Logic adapter cards on PCI-based machines. Refer to  
Section 4.3.1, “Installing the itmpt Sun SPARC Solaris Driver,for  
information on installing the itmpt device driver.  
4.3.1 Installing the itmpt Sun SPARC Solaris Driver  
The LSI Logic LSI7202CP uses the itmpt driver for Solaris systems. This  
driver is included with your adapter kit. The following sections describe  
the procedures to install the itmpt driver on Solaris based systems.  
Note:  
If you plan to use an LSI Logic adapter for your system  
disk, you must use the installation procedure as described  
in Section 4.3.1.2, “Network Installation Procedure,to load  
the device driver during installation.  
4.3.1.1 Existing System Installation  
These instructions provide details on how to install the LSI Logic itmpt  
driver to an existing Solaris operating system.  
Note:  
You must be logged on as root to perform the installation.  
4-4  
Solaris Software Requirements  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
     
Floppy Disk Install – If you received the drivers on a floppy diskette,  
follow these steps:  
Step 1. Place the diskette in the floppy drive and execute the volcheck  
command to ensure the system sees the floppy.  
Step 2. Execute the pkgadd procedure to add the itmpt driver to the  
operating system.  
Example: pkgadd -d floppy/floppy0  
You will see the display on the screen as shown in Figure 4.1 and  
Figure 4.2.  
Figure 4.1 pkgadd Procedure  
The following packages are available:  
1 TImpt LSI Logic/IntraServer FusionMPT(tm)  
Fibrechannel/SCSI drivers  
(sparc) itmpt kit version 1.1  
Select package(s) you wish to process (or 'all' to process  
all packages). (default: all) [?,??,q]: 1  
Processing package instance <ITImpt> from  
</floppy/intraserver>  
LSI Logic/IntraServer FusionMPT(tm) Fibrechannel/SCSI  
drivers (sparc) itmpt kit version 1.1  
IntraServer Technology, Inc / LSI Logic  
Using </> as the package base directory.  
## Processing package information.  
## Processing system information.  
2 package pathnames are already properly installed.  
## Verifying disk space requirements.  
## Checking for conflicts with packages already installed.  
## Checking for setuid/setgid programs.  
itmpt Device Driver  
4-5  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
       
Figure 4.2 Completing Floppy Disk Installation  
This package contains scripts which will be executed with  
superuser permission during the process of installing this  
package.  
Do you want to continue with the installation of <ITImpt>  
[y,n,?] y  
Installing LSI Logic/IntraServer FusionMPT(tm)  
Fibrechannel/SCSI drivers as <ITImpt>  
## Installing part 1 of 1.  
/kernel/drv/itmpt  
/kernel/drv/itmpt.conf  
[ verifying class <none> ]  
## Executing postinstall script.  
installing /kernel/drv/sparcv9/itmpt  
Installation of <ITImpt> was successful.  
Step 3. The itmpt device driver is now installed. Reboot the machine to  
reconfigure the system and to recognize the new devices.  
Distribution File Install – If you received the drivers in an  
itmpt_install.tar.Z file, follow these steps:  
Step 1. Uncompress and untar the itmpt_install.tar.Z file by typing the  
following commands to create a directory named install:  
uncompress itmpt_install.tar.Z  
tar -xvf itmpt_install.tar  
cd install  
Step 2. Execute the pkgadd process as described in the previous  
section to add the itmpt driver to the operating system:  
Note:  
If you change the disk drive configuration of your machine,  
it may be necessary to issue the command:  
touch /reconfigure  
and then reboot the system to allow the system to detect  
and correctly install your new disks.  
4-6  
Solaris Software Requirements  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
   
4.3.1.2 Network Installation Procedure  
If you are using your LSI Logic adapter to support your Sparc Solaris  
system disk, you must install the Solaris operating system using a  
network install. This section describes a complete installation of the  
Solaris operating system to a client system using LSI Logic adapters for  
the system disk. The method described in this section allows you to  
install the LSI Logic itmpt driver onto a network boot kit, making it  
available during the Sparc installation process.  
If you are simply installing an LSI Logic adapter as an additional storage  
adapter in an existing system, use the driver installation procedure  
described in the “Distribution File Install” portion of Section 4.3.1.1,  
“Existing System Installation.”  
Setting up a Boot/Install Server – Refer to the “Preparing to Install  
Solaris Software Over the Network,section of the Solaris Advanced  
The basic steps to set up a boot and install server are as follows:  
Step 1. Insert the Solaris distribution CD in the boot/install server’s CD-  
ROM drive.  
Step 2. Change your directory to the Tools area on the distribution CD:  
cd /cdrom/cdrom0/Solaris_2.8/Tools  
Step 3. Use the setup_install_server script to copy the boot and  
installation files to the boot/install server:  
./setup_install_server /export/home/install  
Installing the itmpt Driver on the Boot/Install Server – After you  
have set up the network boot and install server, follow these steps to run  
the install.sh script, using the nparameter to copy the driver kit to  
the boot server’s boot files:  
Step 1. Place the diskette in the floppy drive and execute the volcheck  
command to ensure the system sees the floppy.  
Step 2. Change the directory to the root of the floppy:  
cd /floppy/floppy0  
Step 3. Execute the install.sh shell script to add the itmpt driver to  
the boot installation area:  
itmpt Device Driver  
4-7  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
./install.sh –n /export/home/install/Solaris_2.8  
Notes:  
For Solaris 2.7 boot files, the installation directory is  
/export/home/install/Solaris_2.7.  
For Solaris 2.6 boot files, the installation directory is  
/export/home/install/Solaris_2.6.  
You can safely ignore the message: “major number  
maximum based on server, not client.”  
Running the install.shscript this way copies and installs the LSI Logic  
drivers into the Tools/Boot/ area of the boot files and allows LSI Logic  
adapters to be booted for installation using the bootserver.  
Adding Clients to Your Boot/Install Server – For each machine that  
boots into the boot/install server, follow these steps to add a client entry  
on the boot/install server:  
Step 1. Change the directory to the boot/install kit:  
cd /export/home/install/Solaris_2.8/Tools  
Step 2. Use the add_install_client script to add the client machine  
./add_install_client -i ipaddr  
-e ethernetid client_name platform_group  
Where:  
ipaddr  
is the tcp/ip address of the client  
ethernetid  
is the ethernet hardware (mac) address of  
the client  
client_name  
is the client’s system name  
platform_group is the client’s vendor defined hardware  
group  
Example: ./add_install_client -i 192.168.103.124 –e  
00:08:26:02:25:34 sunsys sun4u  
Note:  
You can obtain the platform_group from a machine of the  
same type as the target client using the uname –m  
command.  
Booting the Client Using the itmpt FC Driver – Now you can begin  
the installation of the Solaris operating system to the client target  
4-8  
Solaris Software Requirements  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
machine using the boot and install server. On the client machine, boot  
the network install kit you created in the preceding steps as follows:  
ok boot net -v  
Important: Choose “Manual Reboot” rather than “Auto Reboot” during  
the installation of Solaris on the target machine. If you  
choose “Auto Reboot”, you will not have the opportunity to  
complete the installation of the LSI Logic drivers and your  
system will fail to boot.  
After the installation is complete and the system is waiting to be manually  
rebooted, proceed to a console window and run the following script:  
/sbin/itmptinst  
This script copies and installs the drivers from the boot server to the  
newly created Solaris installation. After this script is run, the LSI Logic  
device driver installation is complete and the system can be rebooted.  
Notes:  
You can safely ignore the message: “major number  
maximum based on server, not client.”  
Your Sun machine will prompt you to allow power saving  
automatic shutdown. You must answer no to this question  
if you are using the LSI Logic adapter to support your boot  
disk.  
If you change the disk drive configuration of your machine,  
it may be necessary to issue the command:  
touch /reconfigure  
and then reboot the system to allow it to detect and cor-  
rectly install your new disks.  
4.3.1.3 Troubleshooting the itmpt Device Driver  
Table 4.1 lists some potential error messages. In the message  
descriptions below <n> is replaced by a number that the operating  
itmpt Device Driver  
4-9  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
system assigns. This number helps to identify the bus that is reporting  
the error.  
Table 4.1  
Error Messages  
Error Messages  
Explanation  
itmpt<n>: This hardware not  
supported by this driver.  
itmpt has been told to control an MPT device that is made by a  
manufacturer other than LSI Logic/IntraServer. This adapter  
requires a special driver provided by that manufacturer. Please  
contact the manufacturer for assistance.  
itmpt<n>: Failed to map device  
registers.  
itmpt was unable to access the hardware registers necessary  
for operation. The operating system did not properly configure  
the PCI device. Make sure your adapter has LSI Logic Fcode,  
and that the adapter is working correctly at the SUN Open Boot  
PROM (OBP) prompt.  
itmpt<n>: Hardware not properly  
enabled by system, cmd=xxxxh.  
The system has not properly enabled the configuration  
resources that itmpt needs in order to use this hardware. The  
cmd=xxxxh value must be reported to LSI Logic technical  
support.  
itmpt<n>: Could not allocate  
The driver was unable to allocate memory required to process  
memory to read configuration data. the configuration data. This means that the configuration was  
not properly determined. To x this, you may need to manually  
configure the driver using the itmpt.conf file.  
itmpt<n>: Unable to make reset  
notification callbacks.  
The itmpt was unable to notify the target device driver of a bus  
reset. The target driver may start to malfunction.  
itmpt<n>: ddi_dma_unbind_handle: The operating system failed to respond to the named routine in  
failed  
a known manner. This is a fatal error that is not recoverable.  
Please report this error to technical support.  
itmpt<n>: ddi_dma_numwin() failed.  
itmpt<n>: ddi_dma_getwin() failed.  
itmpt<n>: ddi_dma_alloc_handle:  
xxh unknown/impossible.  
itmpt<n>:  
ddi_dma_buf_bind_handle:  
DDI_DMA_INUSE impossible.  
itmpt<n>:  
ddi_dma_buf_bind_handle: xxh  
unknown/impossible.  
itmpt<n>: No KeyROM found.  
The adapter is not a valid LSI Logic adapter licensed for use  
Hardware contains no valid license. with Solaris systems.  
4-10  
Solaris Software Requirements  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
Table 4.1  
Error Messages (Cont.)  
Error Messages  
Explanation  
itmpt<n>: Hi-level interrupts not  
supported.  
The adapter is in a slot that cannot be used with this driver. Try  
moving the adapter to a different PCI slot.  
itmpt<n>: Device in a slave-only slot  
and is unusable.  
itmpt<n>: Failed to attach. This  
adapter will not be installed.  
Because of one of the previous two errors, this adapter could  
not be "attached" to the I/O subsystem and is not accessible.  
See the previous error message and solve that problem.  
itmpt<n>: Unable to obtain soft  
state structure.  
The driver was unable to initialize a required data structure and  
therefore did not load. Please call technical support.  
itmpt<n>: Failed to attach interrupt The driver was unable to initialize the interrupt handler as  
handler.  
required. Call technical support.  
itmpt<n>: The adapter is  
The driver is not able to communicate with the hardware. You  
malfunctioning or is of an unknown may need to update your driver or your hardware.  
type.  
itmpt<n>: The adapter is  
malfunctioning.  
itmpt<n>: Failed to create minor  
node required for DMI interface.  
The driver was unable to create an entry point for the DMI  
device driver. If you are not using the DMI device driver, then  
you may safely ignore this message.  
itmpt<n>: Could not attach to the  
SCSI subsystem.  
The driver was unable to communicate with the SCSI/FC device  
driver that is part of the operating system. You may need to  
update your driver.  
itmpt<n>: Failed to allocate  
memory.  
The driver was unable to allocate the memory needed during  
initialization. You may have run out of available memory.  
itmpt<n>: Unbind failed!  
The driver had a problem when attempting to unload itself.  
This is a fatal error.  
itmpt Device Driver  
4-11  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
4-12  
Solaris Software Requirements  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Appendix A  
Glossary of Terms and  
Abbreviations  
8B/10B  
ANSI  
A data encoding scheme developed by IBM, translating byte wide data  
to an encoded 10-bit format.  
American National Standards Institute, the coordinating organization for  
voluntary standards in the United States.  
Arbitrated Loop  
Topology  
A FC Topology that provides a low cost solution to attach multiple ports  
in a loop without hubs and switches.  
(FC-AL)  
BER  
Bit  
Bit Error Rate.  
A binary digit. The smallest unit of information a computer uses. The  
value of a bit (0 or 1) represents a two-way choice, such as on or off,  
true or false, and so on.  
Broadcast  
Bus  
Sending a transmission to all N_Ports on a fabric.  
A collection of unbroken signal lines across which information is  
transmitted from one part of a computer system to another. Connections  
to the bus are made using taps on the lines.  
Bus Mastering  
A high-performance way to transfer data. The host adapter controls the  
transfer of data directly to and from system memory without bothering  
the computer’s microprocessor. This is the fastest way for multitasking  
operating systems to transfer data.  
Byte  
A unit of information consisting of eight bits.  
Channel  
A point-to-point link, the main task of which is to transport data from one  
point to another.  
LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter A-1  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
   
3.75 pc  
10.25 pc  
11.25 pc  
38.25 pc  
34.5 pc  
4.333 pc  
Configuration  
Refers to the way a computer is setup; the combined hardware  
components (computer, monitor, keyboard, and peripheral devices) that  
make up a computer system; or the software settings that allow the  
hardware components to communicate with each other.  
CPU  
Central Processing Unit. The “brain” of the computer that performs the  
actual computations. The term Microprocessor Unit (MPU) is also used.  
Crosspoint-  
Switched  
Topology  
(FC-XS)  
Highest performance FC fabric, providing a choice of multiple path  
routings between pairs of F_Ports.  
DMA  
Direct Memory Access. A method of moving data from a storage device  
directly to RAM, without using the CPU’s resources.  
DMA Bus  
Master  
A feature that allows a peripheral to control the flow of data to and from  
system memory by blocks, as opposed to PIO (Programmed I/O) where  
the processor is in control and the flow is by byte.  
Device Driver  
EEPROM  
EISA  
A program that allows a microprocessor (through the operating system)  
to direct the operation of a peripheral device.  
44.25 pc  
Electronically Erasable Programmable Read Only Memory. A memory  
chip typically used to store configuration information.  
Extended Industry Standard Architecture. An extension of the 16-bit ISA  
bus standard. It allows devices to perform 32-bit data transfers.  
Exchange  
Fabric  
A term that refers to one of the FC “building blocks”, composed of one  
or more nonconcurrent sequences for a single operation.  
FC defined interconnection methodology that handles routing in FC  
networks.  
FC-EP  
The future FC Enhanced Physical standard, which will build on and is  
compatible with FC-PH.  
FC-PH  
FC Physical standard, consisting of the three lower levels;  
FC-0, FC-1, and FC-2.  
FC-0  
Lowest level of the FC Physical standard, covering the physical  
characteristics of the interface and media.  
48.583 p  
52.5 pc  
A-2  
Glossary of Terms and Abbreviations  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
3.75 pc  
10.25 pc  
11.25 pc  
38.25 pc  
34.5 pc  
4.333 pc  
FC-1  
FC-2  
FC-3  
FC-4  
Middle level of the FC-PH standard, defining the 8B/10B  
encoding/decoding and transmission protocol.  
Highest level of FC-PH, defining the rules for signaling protocol and  
describing transfer of the frame, sequence, and exchanges.  
The hierarchical level in the FC standard that provides common services,  
such as striping definition.  
The hierarchical level in the FC standard that specifies the mapping of  
Upper Layer Protocols (ULPs) to levels below.  
FCC  
FCP  
FDDI  
Federal Communications Commission.  
Fibre Channel Protocol.  
Fiber Distributed Data Interface. ANSI option for a Metropolitan Area  
Network (MAN); a network based on the use of optical fiber cable to  
transmit data at 100 Mbits/s.  
Fibre Channel  
Service  
The common FC-4 level protocol for all services, transparent to the fabric  
type or topology.  
Protocol (FSP)  
44.25 pc  
File  
A named collection of information stored on a disk.  
Firmware  
Software that is permanently stored in ROM. Therefore, it can be  
accessed during boot time.  
F_Port  
“Fabric” port, the access point of the fabric for physically connecting the  
user’s N_Port.  
FL_Port  
Frame  
An F_Port that contains arbitrated loop functions.  
A linear set of transmitted bits that define a basic transport element.  
Hard Disk  
A disk made of metal and permanently sealed into a drive cartridge. A  
hard disk can store very large amounts of information.  
HAL  
Hardware Abstraction Layer.  
HIPPI  
High Performance Parallel Interface, an 800 Mbits/s interface to  
supercomputer networks (formerly known as high speed channel)  
developed by ANSI.  
48.583 p  
52.5 pc  
A-3  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
3.75 pc  
10.25 pc  
11.25 pc  
38.25 pc  
34.5 pc  
4.333 pc  
Host  
The computer system in which a SCSI host adapter is installed. It uses  
the SCSI host adapter to transfer information to and from devices  
attached to the SCSI bus.  
Host Adapter  
A circuit board or integrated circuit that provides a SCSI bus connection  
to the computer system.  
IP  
Internet Protocol.  
IPI  
ISA  
Intelligent Peripheral Interface.  
Industry Standard Architecture. A type of computer bus used in most  
PCs. It allows devices to send and receive data up to 16 bits at a time.  
Kbyte  
LCT  
Kilobyte. A measure of computer storage equal to 1024 bytes.  
Logical Configuration Table.  
LLC  
Logical Link Control.  
Local Bus  
A way to connect peripherals directly to computer memory. It bypasses  
the slower ISA and EISA buses. PCI is a local bus standard.  
44.25 pc  
L_Port  
A FC port which supports the arbitrated loop topology.  
Link_Control_  
Facility  
A termination card that handles the logical and physical control of the FC  
link for each mode of use.  
Login Server  
LUN  
Entity within the FC fabric that receives and responds to login requests.  
Logical Unit Number. An identifier, zero to seven, for a logical unit.  
Megabyte. A measure of computer storage equal to 1024 kilobytes.  
Message Frame Address.  
Mbyte  
MFA  
Multicast  
NIC  
Refers to delivering a single transmission to multiple destination N_Ports.  
Network Interface Card.  
N_Port  
NL_Port  
“Node” port, a FC defined hardware entity at the node end of a link.  
An N_Port that contains arbitrated loop functions.  
48.583 p  
52.5 pc  
A-4  
Glossary of Terms and Abbreviations  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
3.75 pc  
10.25 pc  
11.25 pc  
38.25 pc  
34.5 pc  
4.333 pc  
Operating  
System  
A program that organizes the internal activities of the computer and its  
peripheral devices. An operating system performs basic tasks such as  
moving data to and from devices, and managing information in memory.  
It also provides the user interface.  
Operation  
A term, defined in FC-2, that refers to one of the FC “building blocks”  
composed of one or more, possibly concurrent, exchanges.  
Ordered Set  
A FC term referring to four 10-bit characters (a combination of data and  
special characters) that provide low level link functions, such as frame  
demarcation and signaling between two ends of a link. It provides for  
initialization of the link after power-on and for some basic recovery  
actions.  
Originator  
A FC term referring to the initiating device.  
Parity Checking A way to verify the accuracy of data transmitted over the SCSI bus. One  
bit in the transfer is used to make the sum of all the 1 bits either odd or  
even (for odd or even parity). If the sum is not correct, an error message  
appears.  
PCI  
Peripheral Component Interconnect. A local bus specification that allows  
connection of peripherals directly to computer memory. It bypasses the  
slower ISA and EISA buses.  
44.25 pc  
PDB  
PIO  
Packet Descriptor Block.  
Programmed Input/Output. A way the CPU can transfer data to and from  
memory using the computer’s I/O ports. PIO is usually faster than DMA,  
but requires CPU time.  
Port  
The hardware entity within a node that performs data communications  
over the FC link.  
Port Address  
Also Port Number. The address through which commands are sent to a  
host adapter board. This address is assigned by the PCI bus.  
Port Number  
RAM  
See Port Address.  
Random Access Memory. The computer’s primary working memory in  
which program instructions and data are stored and are accessible to the  
CPU. Information can be written to and read from RAM. The contents of  
RAM are lost when the computer is turned off.  
48.583 p  
52.5 pc  
A-5  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
3.75 pc  
10.25 pc  
11.25 pc  
38.25 pc  
34.5 pc  
4.333 pc  
Responder  
A FC term referring to the answering device.  
RISC Core  
LSIFC909 chips contain a RISC (Reduced Instruction Set Computer)  
processor, programmed through microcode scripts.  
ROM  
Read Only Memory. Memory from which information can be read but not  
changed. The contents of ROM are not erased when the computer is  
turned off.  
SAN  
Storage Area Network.  
SCAM  
SCSI Configured AutoMatically. A method to automatically allocate SCSI  
IDs using software when SCAM compliant SCSI devices are attached.  
Scatter/Gather  
A device driver feature that lets the host adapter modify a transfer data  
pointer so that a single host adapter transfer can access many segments  
of memory. This minimizes interrupts and transfer overhead.  
SCB  
SCSI Command Block.  
SCSI  
Small Computer System Interface. A specification for a high-performance  
peripheral bus and command set. The original standard is referred to as  
SCSI-1.  
44.25 pc  
SCSI-2  
The current SCSI specification which adds features to the original  
SCSI-1 standard.  
SCSI ID  
A way to uniquely identify each SCSI device on the SCSI bus. Each  
SCSI bus has eight available SCSI IDs numbered 0 through 7 (or 0  
through 15 for Wide SCSI). The host adapter usually gets ID 7 giving it  
priority to control the bus.  
Sequence  
A term referring to one of the FC “building blocks”, composed of one or  
more related frames for a single operation.  
SGL  
Scatter Gather List.  
SNAP  
SubNetwork Access Protocol.  
Synchronous  
Data Transfer  
One of the ways data is transferred over the SCSI bus. Transfers are  
clocked with fixed frequency pulses. This is faster than asynchronous  
data transfer. Synchronous data transfers are negotiated between the  
SCSI host adapter and each SCSI device.  
48.583 p  
52.5 pc  
A-6  
Glossary of Terms and Abbreviations  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
3.75 pc  
10.25 pc  
11.25 pc  
38.25 pc  
34.5 pc  
4.333 pc  
System BIOS  
Controls the low level POST (Power-On Self-Test), and basic operation  
of the CPU and computer system.  
TID  
Target ID.  
Topology  
ULP  
The logical and/or physical arrangement of stations on a network.  
Upper Layer Protocol.  
VCCI  
Voluntary Control Council for Interference.  
Space on a hard disk that can be used as if it were RAM.  
Vendor Product Data.  
Virtual Memory  
VPD  
Word  
A two-byte (or 16-bit) unit of information.  
X3T9  
A technical committee of the Accredited Standards Committee X3, titled  
X3T9 I/O Interfaces. It is tasked with developing standards for moving  
data in and out of central computers.  
44.25 pc  
48.583 p  
52.5 pc  
A-7  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
3.75 pc  
10.25 pc  
11.25 pc  
38.25 pc  
34.5 pc  
4.333 pc  
44.25 pc  
48.583 p  
52.5 pc  
A-8  
Glossary of Terms and Abbreviations  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Index  
floppy disk installation  
itmpt device driver 4-5, 4-6  
form factor 2-5  
A
adapter properties menu 3-3  
atmospheric characteristics 2-6  
Fusion-MPT 2-1  
B
heat sink 2-6  
host adapter installation 1-1  
hot swap 2-4  
BSMI 2-6  
bus interfaces 2-3  
extraction 1-3  
installation 1-2  
C
Canadian Compliance Statement 2-6  
CE mark 2-6  
characteristics  
electrical 2-5  
physical 2-5  
hot swap 1-2  
itmpt  
safety 2-6  
cold  
extraction 1-3  
installation 1-1  
command  
floppy disk 4-5, 4-6  
pkgadd 4-5  
volcheck 4-5  
CompactPCI 2-4, 2-5  
form factor 2-5  
hot swap 2-4  
LED  
power 1-1, 1-3  
Linux 2-1, 2-2  
D
M
device driver 3-1, 4-1  
installation 3-1, 4-1  
menus  
device properties menu 3-4  
E
electrical characteristics 2-5  
electromagnetic compliance 2-6  
existing system installation  
Solaris itmpt device driver  
floppy disk installation 4-5, 4-6  
extraction  
O
NetWare 2-1, 2-2  
SCO OpenServer 2-1, 2-2  
Solaris 2-1  
cold environment 1-3  
hot swap environment 1-3  
hot-swap environment 1-3  
UnixWare 2-1, 2-2  
F
P
FCC Class A 2-6  
FCC Self-Certification log 2-6  
PCI 2-4, 2-5  
physical characteristics 2-5  
LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter  
IX-1  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
 
pkgadd 4-5  
power  
characteristics 2-5  
LED 1-1, 1-3  
S
safety characteristics 2-6  
SCO OpenServer 2-1, 2-2  
SCSI 2-4  
software support 2-1, 2-2  
Solaris 2-1  
storage environment 2-6  
T
technical specifications 2-3, 2-5  
atmospheric characteristics 2-6  
electrical characteristics 2-5  
electromagnetic compliance 2-6  
heat sink 2-6  
physical characteristics 2-5  
power characteristics 2-5  
storage environment 2-6  
thermal characteristics 2-6  
transit environment 2-6  
thermal characteristics 2-6  
transit environment 2-6  
U
UL flammability rating 2-6  
UnixWare 2-1, 2-2  
V
VCCI 2-6  
volcheck 4-5  
IX-2  
Index  
Copyright © 2001, 2002 by LSI Logic Corporation. All rights reserved.  
 
Customer Feedback  
We would appreciate your feedback on this document. Please copy the  
following page, add your comments, and fax it to us at the number  
shown.  
If appropriate, please also fax copies of any marked-up pages from this  
document.  
Important: Please include your name, phone number, fax number, and  
company address so that we may contact you directly for  
clarification or additional information.  
Thank you for your help in improving the quality of our documents.  
LSI7202CP CompactPCI Dual Channel 2 Gbit/s Fibre Channel Host Adapter  
 
 
Reader’s Comments  
Fax your comments to:  
LSI Logic Corporation  
Technical Publications  
M/S E-198  
Fax: 408.433.4333  
Please tell us how you rate this document: LSI7202CP CompactPCI Dual  
Channel 2 Gbit/s Fibre Channel Host Adapter User’s Guide. Place a  
check mark in the appropriate blank for each category.  
Excellent Good Average Fair  
Poor  
____  
____  
____  
____  
____  
Completeness of information  
Clarity of information  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
____  
Ease of finding information  
Technical content  
Usefulness of examples and  
illustrations  
Overall manual  
____  
____  
____  
____  
____  
What could we do to improve this document?  
If you found errors in this document, please specify the error and page  
number. If appropriate, please fax a marked-up copy of the page(s).  
Please complete the information below so that we may contact you  
directly for clarification or additional information.  
Name  
Date  
Telephone  
Title  
Fax  
Department  
Company Name  
Street  
Mail Stop  
City, State, Zip  
 
 
You can find a current list of our U.S. distributors, international distributors, and sales  
offices and design resource centers on our web site at  
 

Lennox Hearth Indoor Fireplace ADK22CMBS User Manual
Lennox Hearth Indoor Fireplace Cambria User Manual
Lenovo Laptop Docking Station 0A33932 User Manual
LG Electronics Microwave Oven MV 1310B User Manual
LG Electronics Range LRE30755SB User Manual
Liebert Automobile Alarm RCM8CE User Manual
Lincoln Electric Welder IM10030 User Manual
Lindy Personal Computer 25018 User Manual
Link electronic Switch PAF 823 User Manual
Logitech Mouse G700 User Manual