FULL MANUAL
OPERATING INSTRUCTIONS
DIRECT DRIVE TURNTABLE
T.6O
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
21. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and power-line surges.
22. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
23. Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.
CAUTION: To reduce the risk of electric shock, do not
CAUTION
remove any cover. No user-serviceable parts inside. Refer
servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the
use to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operation and maintenance (servicing) instructions in the literature accompanying
this appliance.
CAUTION
To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent blade exposure.
ŸThis device complies with Part 15 of the FCC Rules Operation is Subject to the following two conditions (1) This
device may not Cause harmful interference, and (2) this device must accept any Interference received. Including
interference that may cause Undesired operation.
ŸThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
ŸUnauthorized modification of this unit may cause it to no longer comply with FCC regulations and void your
authority to use this device.
ŸCet appareil numérique de la classe B respecte toutes les exigencies du Rèsur le materiel brouilleur du Canada.
NAME OF PARTS
15 14
1
13
12
2
3
4
11
10
9
5
1
6 7
8
1) Start/Stop Button
2) Strobe Dots
3) Slip Mat
9) Pitch Control Slider
10) Headshell Locking Nut
11) Tonearm
4) Center Spindle
5) Power Switch
6) 33 Button
12) Arm Rest
13) Counterweight
14) 45-rpm Adaptor
7) 45 Button
15) Position For Preparing Cartridge
8) Target Light base
16 17
18
16) Phono Output
18) Power cord connector
17) GND
BEFORE USE
*Check following parts included in the package with the
main unit:
1) Turntable platter
8) Target light
9) AC cord
10) Cloth dust cover
2) Slip mat
3) 45-rpm adaptor
4) Counterweight
*Notes:
1) Do not connect the AC power plug before assembly
has been completed.
5) 500B cartridge and Headshell, except on model
T.60X, no cartridge included.
6) Operating instructions
7) RCA Cables with ground wire
2) Read this manual carefully before using the unit
and be sure to store the manual in a safe place for
future reference.
ASSEMBLY
1. Remove the main unit with the packing from the
box and take off the packing.
2. Insert the turntable platter onto the center spindle.
3. Set the slip mat on the platter.
4. Installation of cartridge:
6. Slide counterweight onto tonearm. Twist it lightly
and it will screw onto the rear shaft of the tonearm.
7. Adjustment of horizontal zero (0) balance and
stylus pressure:
(a) Remove the stylus protector, do not touch the
stylus tip during the adjustment.
(b) Release the arm clamp and lift the tonearm
from the arm rest to free it.
(c) Rotate the counterweight until the tonearm is
approximately balanced horizontally (floats
freely).
(d) Refasten the tonearm with the arm clamp.
(e) Hold the counterweight stationary with one
hand and rotate only the stylus-pressure ring to
bring the number "0" of the ring into alignment
with the center line on the tonearm rear shaft.
(f) Rotate the counterweight clockwise until the
scale shows the value corresponding to the
pressure of the used stylus. The average stylus
pressure of the cartridge body is 1.5-2 g. If you
use a non-Stanton cartridge, please follow that
manufacturer’s instructions.
When installing a cartridge, refer to the operating
instructions of that cartridge.
During installation, attach the stylus protector to
guard the stylus tip from damage.
(1) Connect the lead wires to the cartridge
terminals. The terminals of most cartridges are
color coded.
Connect each lead wire to the terminal of the
same color.
White (L+)
Blue (L-)
Red (R+)
Green (R-)
Left channel+
Left channel-
Right channel+
Right channel-
(2) Install the cartridge to the headshell and
tighten it with screws provided with the
cartridge.
5. Insert the headshell into the front end of the
tonearm, then turn the lock nut clockwise with the
headshell firmly held horizontally.
8. Install the cloth dust cover to the main unit.
PLACEMENT
location which is very stable and vibration free.
· The legs have functions for adjusting the height of the
unit itself. Adjust the legs to stabilize the main body
horizontally.
· Do not place the unit in a location where it will be
exposed to direct sunlight or near a heating
appliance.
· Do not place the unit in a location where there is high
humidity or a lot of dust.
· Cartridge may pick up slight sound pressures or
vibrations from the speakers coming along the floor
or through the air resulting in feedback. Find a
CONNECTIONS
1. Connect the power cord to the auxiliary power outlet
NOTE:
on the rear panel of your amplifier or receiver or to a ŸBe sure to connect the ground terminal firmly to the
household AC outlet. amplifier or receiver.
2. Connect the unit output terminals to the PHONO jack ŸIf this connection is not made or is loose, a power
of your amplifier or receiver.
Output terminals
source "HUM" will result.
Amplifier(Receiver)
L Channel
L (White)
R (Red)
>>
>>
>>
R Channel
GND
GND (Spade)
OPERATION
1. Rotate the power dial clockwise to turn on the
power, the speed indicator and the
strobe-illuminator will light up.
2. Place a record on the slip mat, when playing a
45rpm record with a large center hole, place the
45-rpm adaptor on the center spindle.
5. Press the Start/Stop button, the turntable platter will
start to rotate.
6. Move the tonearm over the desired groove.
7. When play is finished, move the tonearm to the arm
rest, secure the tonearm with the arm clamp.
8. Press the Start/Stop button to stop the platter
rotating, rotate the power dial to turn off the power.
3. Set the speed to match the record.
4. Remove the stylus protector, release the arm clamp.
MAINTENANCE
· For best results & proper care of your equipment use
Stanton Vinyl Cleaner (VC-1) for your records and Stylus
Cleaner Kit for styli (SC-4).
· Clean the stylus periodically with a soft brush to
prevent the accumulation of dust.
· When the sound becomes distorted or noisy, check
the stylus. If worn out, replace it with a new one.
· Any volatile materials such as alcohol, thinner, benzine,
etc., may remove the paint or damage the lustre,
please avoid.
SPECIFICATIONS
APPLICATION:
This specification applies to the direct drive turntable unit T.60
STANDARD TEST CONDITION:
Ambient Temperature
Relative Humidity
20 +/- 2 degC
65% +/- 5%
NOTE: Measurements can be carried out between 5 degC to 35 degC and 45% to 85% relative humidity.
TURNTABLE SECTION:
Type
2-speed full manual
Motor
Speeds
8pole, 2phase,brushless DC motor
1
33 /
3
and 45rpm
1
Wow and Flutter
Pitch Controls
Starting Torque
Starting Time
Braking Time
Time for Speed Change
Less than 0.15% WRMS (JIS WTD) with 33 /3rpm
+/-10%
More than 1 kgf.cm
Less than 1 sec. with 33 /3rpm
Less than 1 sec. with 33 /3rpm
Less than 1 sec. from 33 /
Less than 1 sec. from 45 to 33 /
Phono output
1
1
1
3
to 45 rpm.
1
3
rpm.
Audio Output
SPECIFICATIONS
TONEARM SECTION:
Type
Static balanced straight shaped tonearm with cardan’s suspension
Effective Arm Length
Tracking Force Adjustment Range
Applicable Cartridge Weight
191mm
0~4g
6~10g
CARTRIDGE SECTION:
Channel Separation
Channel Balance
More than 14 dB
Within 2.5dB at 1KHz
1.5~2g
Needle Pressure range
GENERAL SECTION:
Power Supply
AC 100V, 50/60Hz (For Japan)
AC 110V, 60Hz (For Taiwan)
AC 120V, 60Hz (For U.S.A.,Canada,Mexico)
AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina)
AC 220V, 60Hz (For Philippines)
AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel)
AC 240V, 50Hz (For Australia,U.K.)
Power Consumption
Dimensions
Weight
7.5 Watts
452 (W) x 370 (D) x 86 (H) mm
6.3 Kgs
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement
WARRANTY
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S.,
will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the
replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the
date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days
following the date of original purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and
Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
RETURNS
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring
warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from
whom the merchandise was purchased and in the same country where the merchandise was purchased. For purposes of
purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the country where the
authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton dealer in the
country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-authorized
dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth
above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and
follow such authorized Stanton dealer’s return policy.
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application
made of the merchandise. Stanton's liability for any claim, whether based on breach of contract, negligence, infringement of any
rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by Stanton from your
purchase of such merchandise. In no event will Stanton be liable for any special, incidental or consequential damages (including
loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Stanton or otherwise. To the
extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied warranties of
merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation
from state to state and country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please
include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.
c u t a l o n g d o t t e d l i n e
PLACE
STAMP
HERE
Stanton Magnetics, Inc.
3000 SW 42nd Street
Hollywood, FL 33312
U.S.A.
|