Sun Microsystems Network Card LSI22320 SR User Manual

Sun StorEdge™ PCI/PCI-X Dual  
Ultra320 SCSI Host Adapter  
Installation Guide  
Sun Microsystems, Inc.  
Part No. 817-5827-13  
January 2007, Revision A  
Submit comments about this document at: http://www.sun.com/hwdocs/feedback  
 
Preface  
This Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide is  
intended for experienced system administrators.  
Before You Read This Book  
Before you install and use the Sun StorEdge™ PCI/PCI-X Dual Ultra320 SCSI host  
adapter as described in this manual, you must read and understand the documents  
listed in the following table.  
Topic  
Title  
Part Number  
Release Notes  
Sun StorEdge PCI/PCI-X Dual  
Ultra320 SCSI Host Adapter Release  
Notes  
817-5828-xx  
The release notes list supported  
cables, platforms, and storage  
devices along with other essential  
information. See To Access the  
Diagnostics  
SunVTS 5.x User Guide  
Varies according to the SunVTS  
software version being used. A  
different version of the SunVTS  
software is released with each  
release of the Solaris operating  
system  
SunVTS 5.x Reference Manual  
v
 
     
How This Book Is Organized  
Chapter 1 describes the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter  
and explains how to install it on your system, connect it to a storage device, and  
test it. It also includes instructions on booting from a hard disk connected to the  
host adapter.  
Appendix A provides general information and configuration rules about the host  
adapter.  
Appendix B contains the specifications for the low-voltage differential (LVD) host  
adapter.  
Appendix C contains the Declaration of Conformity, regulatory, and essential  
safety information.  
Using UNIX Commands  
This document might not contain information on basic UNIX commands and  
procedures such as shutting down the system, booting the system, and configuring  
devices. See the following for this information:  
®
Software documentation that you received with your system  
Solaris™ operating environment documentation, which is at  
vi Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
 
Typographic Conventions  
*
Typeface  
Meaning  
Examples  
AaBbCc123  
The names of commands, files,  
and directories; on-screen  
computer output  
Edit your.loginfile.  
Use ls-ato list all files.  
% You have mail.  
What you type, when contrasted % su  
with on-screen computer output  
AaBbCc123  
Password:  
Book titles, new words or terms, Read Chapter 6 in the User’s Guide.  
AaBbCc123  
words to be emphasized.  
Replace command-line variables  
with real names or values.  
These are called class options.  
You must be superuser to do this.  
To delete a file, type rmfilename.  
*
The settings on your browser might differ from these settings.  
Related Documentation  
Application  
Title  
Part Number  
Installation  
817-5828-xx  
Sun StorEdge PCI/PCI-X Dual  
Ultra320 SCSI Host Adapter  
Release Notes  
817-6237-10  
Sun StorEdge PCI/PCI-X Dual  
Ultra320 SCSI Host Adapter  
Guide to Documentation  
Preface  
vii  
 
Accessing Sun Documentation  
You can view, print, or purchase a broad selection of Sun documentation, including  
localized versions, at:  
To access Solaris OS usage documents listed under “Using UNIX Commands” on  
page vi and the SunVTS™ software documents listed in “Before You Read This  
Book” on page v, go to docs.sun.com. To access the Sun StorEdge PCI/PCI-X Dual  
Ultra320 SCSI Host Adapter Release Notes at Sun’s Network Storage documentation  
web site, follow the steps on the next page.  
To Access the Release Notes  
1. Access the release notes at Sun’s web site by using one of the following methods.  
Go to www.sun.comand follow these links:  
a. Click Products & Services.  
b. Under Browse Products, click Storage.  
c. In the right frame, under Use, click Documentation.  
d. Under Hardware/Storage, click StorEdge.  
Alternately, you can go directly to this address:  
2. From the product list, click Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI  
3. In the documentation list, click the row listing the Sun StorEdge PCI/PCI-X Dual  
Ultra320 SCSI Host Adapter Release Notes.  
Note – Viewing and printing documents in Adobe® Portable Document Format  
(PDF) requires Adobe Acrobat Reader, which is downloadable for free from:  
viii Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
   
Third-Party Web Sites  
Sun is not responsible for the availability of third-party web sites mentioned in this  
document. Sun does not endorse and is not responsible or liable for any content,  
advertising, products, or other materials that are available on or through such sites  
or resources. Sun will not be responsible or liable for any actual or alleged damage  
or loss caused by or in connection with the use of or reliance on any such content,  
goods, or services that are available on or through such sites or resources.  
Contacting Sun Technical Support  
If you have technical questions about this product that are not answered in this  
document, go to:  
Sun Welcomes Your Comments  
Sun is interested in improving its documentation and welcomes your comments and  
suggestions. You can submit your comments by going to:  
Please include the title and part number of your document with your feedback:  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide, part  
number 817-5827-13  
Preface  
ix  
 
x
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
CHAPTER  
1
Installing, Connecting, and Testing  
the Host Adapter  
This chapter describes the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter  
and explains how to install it into a host, connect it to SCSI storage devices, test the  
installation, and boot from a disk drive connected to the host adapter.  
Note – If you are unfamiliar with Ultra320 SCSI configuration guidelines, read  
“Ultra320 SCSI Configuration” on page 13 before performing the procedures in this  
chapter.  
This chapter discusses the following topics:  
1
 
   
Features  
The Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter is a dual-channel  
Ultra320 SCSI to PCI/PCI-X host adapter that provides two Ultra320 SCSI channels.  
FIGURE 1-1 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter  
The host adapter includes the following features:  
Two independent Ultra320 SCSI channels with support for SCSI speeds of up to  
320 Mbyte/sec with 16-bit data transfer  
Four SCSI connectors:  
Two external 68-pin very high density cable interconnect (VHDCI) right-angle  
connectors  
Two internal 68-pin high density right-angle connectors. .  
LVD SCSI support for disk arrays, tape libraries, and tape drives:  
Two 16-bit LVD interfaces with support for up to 15 targets on each SCSI bus  
Active LVD termination  
32K bytes of NVSRAM (reserved feature)  
Backward-compatible with SCSI-2 and SCSI-3 (Ultra1, Ultra2, and Ultra3) devices.  
For Sun StorEdge systems qualified and supported with this host adapter, see Sun  
StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Release Notes, 817-5828-xx.  
2
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
 
512K bytes of Flash ROM for booting in a Sun SPARC or a Sun Solaris x86 OS  
processor-based host system  
A 64-bit universal type board edge connector that provides:  
64-bit, 133-MHz PCI-X interface compatibility  
32-bit/64-bit PCI interface backwards compatibility  
Installing the Host Adapter  
Before you start, read these instructions, and also read the installation instructions in  
the documentation that applies to the storage device(s) to be connected to the host  
adapter. Also, before installing the host adapter, read the Sun StorEdge PCI/PCI-X  
Dual Ultra320 SCSI Host Adapter Release Notes for required information, including  
lists of supported cables and storage devices. Downloading the release notes is  
Caution – This host adapter is only for connection to a single-ended (SE) or low-  
voltage differential (LVD) device, and it does not work if connected to a high-voltage  
differential (HVD) device.  
!
Caution – Damage to the HBA can occur as the result of careless handling or  
electrostatic discharge (ESD). Always handle the HBA with care to avoid damage to  
electrostatic sensitive components.  
To minimize the possibility of ESD-related damage, Sun strongly recommends using  
both a workstation antistatic mat and an ESD wrist strap. You can get an ESD wrist  
strap from any reputable electronics store or from Sun as part number #250-1007.  
Observe the following precautions to avoid ESD-related problems:  
Leave the HBA in its antistatic bag until you are ready to install it in the system.  
Always use a properly fitted and grounded wrist strap or other suitable ESD  
protection when handling the HBA and observe proper ESD grounding  
techniques.  
Hold the HBA by the edge of the PCB or mounting bracket, not the connectors.  
Place the HBA on a properly grounded antistatic work surface pad when it is out  
of its protective antistatic bag.  
Chapter 1 Installing, Connecting, and Testing the Host Adapter  
 
3
 
To Prepare for Hardware Installation  
1. Read and observe the safety information at the back of this book.  
2. Install the Solaris 8 2/04 (minimum required version) operating system on the  
host.  
3. Install the Solaris 8 2/04 (minimum required version) recommended patch cluster  
on the host.  
See the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Release Notes for  
how to download and install the Solaris OS recommended patch cluster.  
4. Install any required driver patches on the host.  
See the release notes to find the applicable patches for the version of the Solaris OS  
that is installed on the host. Also see the release notes for how to download the  
driver and any required patches. If needed, see “To Access the Release Notes” on  
Caution – If the driver and any required patches described in the release notes are  
not installed, you cannot use the host adapter.  
!
5. Install the SunVTS software on the host.  
The SunVTS software is shipped on the Supplemental Software CD-ROM along with  
the Solaris operating system CD-ROM. Read the user’s guide listed in “Before You  
Read This Book” on page v for how to install the SunVTS software.  
6. Exit the operating environment.  
Note – If your system supports the PCI hot-plug capability, refer to the service  
documentation that came with your system. Then continue with Step 8 below.  
To inform any mounted users that the system will be going down, use the shutdown  
command. Otherwise, use the init 0command. See the Man Pages for these  
commans or the Solaris AnswerBook documentation.  
# shutdown  
...  
ok  
7. Power off the system. Refer to the service documentation that came with your  
system.  
4
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
 
Caution – Do not disconnect the power cord from the system or from the wall  
outlet. This connection provides the ground path necessary to safely remove and  
install the printed circuit boards and components without damaging them.  
!
8. Choose a PCI-X (or PCI) slot for installing the host adapter.  
To maximize performance, use the host system’s 64-bit, 66/133-MHz PCI/PCI-X slot  
slot for installing the host adapter.  
Note – You can insert the host adapter into a 32-bit PCI slot if no 64-bit PCI-X slots  
are available. However, if you do this, the data transmission rate is limited to  
standard PCI speed.  
Chapter 1 Installing, Connecting, and Testing the Host Adapter  
 
5
 
9. Unpack the host adapter.  
You should have the following items:  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter (Figure 1-1)  
Antistatic wrist strap  
Note – Leave the host adapter in the protective bag until you are ready to install it.  
J6 connector  
J4 connector  
PCI/PCI-X connector  
J2 (Channel A)  
J3 (Channel B)  
FIGURE 1-2 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter  
VHDCI Connectors  
The host adapter is shown in Figure 1-2. The Very High Density Cable Interconnect  
(VHDCI) connectors are for the VHDCI cables that are used to connect the host  
adapter to the storage device.  
The next section provides instructions on how to install the host adapter in your  
system.  
6
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
To Install the Host Adapter  
1. Open the system.  
Refer to your system documentation for information about how to open the system.  
2. Attach the wrist strap between your wrist and a metal part of the system chassis.  
3. For systems with a standby-type power switch, disconnect the power cord.  
Standby-type power switches have a  
icon.  
The wrist strap between you and the chassis provides the ground path necessary to  
safely remove and install the printed circuit boards and components without  
damaging them.  
4. Remove the filler panel for the desired slot.  
Refer to the system documentation for information about removing filler panels.  
5. Remove the host adapter from its protective bag.  
6. Install the host adapter in the selected PCI/PCI-X slot in your system.  
choose a slot. Also, refer to the system’s hardware documentation for information  
about mounting details (mounting holes, standoff locking/unlocking, and screws to  
secure the card).  
Caution – Using excessive force can bend or damage the host adapter edge  
connector. Make sure that the edge connector is properly aligned before pressing the  
adapter into place. The bracket around the two external connectors should fit into  
the empty space where the filler panel was removed in Step 4.  
!
7. Remove the wrist strap.  
8. Close the system.  
The next two sections describe how to connect the host adapter to one or more  
storage devices and how to test the host adapter.  
Chapter 1 Installing, Connecting, and Testing the Host Adapter  
 
7
   
Connecting the Host Adapter  
Before you connect the host adapter to the storage device(s), do the following:  
Refer to the release notes for the lists of supported cables and storage devices.  
Downloading the release notes is described in “To Access the Release Notes” on  
information on configuration for Ultra320 SCSI devices.  
Refer to your system documentation and the storage device installation manual  
for specific cabling instructions.  
To Connect SCSI Cable(s) From the Host  
Adapter to the Storage Device(s)  
1. Connect the host adapter to the storage device(s) using the appropriate cable(s).  
Refer to Table 1-1 for SCSI interface connection information.  
TABLE 1-1  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Interfaces  
SCSI Interface  
Channel A  
Channel B  
External Connector  
Internal Connector  
J2  
J3  
J6  
J4  
8
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
   
Testing the Host Adapter  
You should test the host adapter installation using the probe-scsi-all command  
and, if the newly attached device is a disk array, with the SunVTS software.  
To Test the Installation Using the probe-scsi-  
allCommand  
1. If you have disconnected the power cable, reconnect it.  
2. Power on the connected storage device(s) and then power on the host.  
3. Bring the system down to the okprompt at run level 0.  
Note – If the host starts to reboot, interrupt the reboot process by  
pressing the Stop and A keys simultaneously.  
4. At the okprompt, enter the probe-scsi-allcommand to verify that the system  
recognizes the host adapter.  
The probe-scsi-allcommand displays the SCSI devices connected to the host, as  
shown in the following screen example.  
ok probe-scsi-all  
/pci@4,2000/pci@1/scsi@2  
Target 0  
Unit 0 DISK SEAGATE ST336605LSUN36G 0238  
/pci@4,2000/pci@1/scsi@2,1  
Target 0  
Unit 0 DISK SEAGATE ST336605LSUN36G 0238  
In this example, the first SCSI port (scsi@2) has one disk drive connected  
(Target 0). The second SCSI port (scsi@2,1) also has one disk drive connected  
(Target 0). In the illustration of the host adapter in Figure 1-1, the first SCSI port is  
labeled as Channel A; the second SCSI port as Channel B.  
Chapter 1 Installing, Connecting, and Testing the Host Adapter  
 
9
   
To Test the Installation With the SunVTS  
Software  
Use the the SunVTS software to test a disk on a newly-attached disk array, to verify  
that the host adapter is properly installed.  
For details about running the the SunVTS software, refer to the SunVTS 5.X User’s  
Guide and the SunVTS 5.X Test Reference Manual.  
1. As superuser, open the SunVTS window.  
# /opt/SUNWvts/bin/sunvts  
2. From the System Map, select a disk drive that is in an array connected to the host  
adapter.  
3. Start the disk test.  
4. Verify that no errors have occurred by checking the SunVTS status window.  
5. If no problems occur, stop the SunVTS software.  
Your host adapter is now ready to run applications.  
Note – If problems occur, please contact your service provider for assistance.  
10  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
 
Booting the Host Adapter  
The Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter uses the mptdriver,  
which is included with the Solaris operating system beginning with the Solaris 8  
2/04 OS release and the Solaris 9 4/04 OS release. This enables you to “warm” boot  
directly from a hard disk connected to the host adapter if that disk has at least the  
Solaris 8 2/04 OS release or the Solaris 9 4/04 OS release installed.  
Note – A “warm” boot requires that the hard disk attached to the host adapter be  
powered on and available at the time the server is powered up. A “cold” boot,  
where both the server and hard disk are powered up at the same time, is not  
supported by the mptdriver.  
After booting, you should install any required patches for the mptdriver. Refer to  
the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Release Notes for  
instructions on dowloading and installing mptdriver patches. To view the Release  
Note – The Sun StorEdge 3310 standalone SCSI array is presently limited to  
Ultra160 SCSI bus speeds only. Normally, the host adapter automatically lowers the  
transfer speed for attached storage devices that are not Ultra320 capable. However,  
for the Sun StorEdge 3310 standalone SCSI array, you must create an mpt.conf file  
to limit the Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter to Ultra160  
SCSI bus speeds.  
For instructions on creating the mpt.conffile, refer to the Sun StorEdge PCI/PCI-X  
Dual Ultra320 SCSI Host Adapter Release Notes. To view the Release Notes, see “To  
Chapter 1 Installing, Connecting, and Testing the Host Adapter  
 
11  
 
12  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
APPENDIX  
A
Ultra320 SCSI Configuration  
This appendix provides general information about Ultra320 SCSI configuration  
rules. The following topics are discussed:  
Target Devices  
For Ultra320 SCSI performance of up to 320 Mbytes/sec, there can be a maximum of  
15 devices connected to each port on the host adapter.  
The available target addresses (SCSI IDs) for each port on the host adapter are 0  
through F.  
Note – The SCSI ID of 7 is reserved for the host adapter.  
13  
 
       
Bus Length  
The maximum SCSI bus length is determined by the SCSI bus type (that is, the  
number of devices connected).  
Table A-1 shows the maximum SCSI bus lengths for Ultra320 SCSI with a 8/16-bit  
bus width.  
TABLE A-1 Bus Restrictions  
SCSI Type  
Peak  
MBytes  
/sec  
Single-Ended  
*
LVD  
No. of Devices  
Max Length  
No. of Devices  
Max Length  
SCSI-2  
Narrow  
10  
20  
3
3
8
25  
12  
25  
12  
2
8
2
16  
Wide  
16  
SCSI-3 Ultra1  
Narrow  
20  
40  
1.5  
3
1.5  
3
8
4
8
4
25  
12  
25  
12  
2
8
2
16  
Wide  
SCSI-3 Ultra2  
Narrow  
\
40  
80  
N/S  
N/S  
N/S  
N/S  
25  
12  
25  
12  
2
8
2
16  
Wide  
SCSI-3 Ultra3  
Narrow  
80  
N/S  
N/S  
N/S  
N/S  
25  
12  
25  
12  
2
8
2
16  
Wide  
160  
SCSI-3 Ultra320  
Narrow  
160  
320  
N/S  
N/S  
N/S  
N/S  
25  
12  
25  
12  
2
8
2
16  
Wide  
*
This maximum length (shown in meters) must include the internal bus length of your system. Sun qualifies  
cable lengths of only up to 10 meters (22.8 feet).  
\ N/S = not supported  
14 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
   
Cabling and Termination  
Use the following cabling guidelines to ensure proper device cabling and  
termination.  
Cabling  
In order to maintain Ultra320 SCSI performance, all cables used must be Ultra320  
SCSI compliant.  
Termination  
The SCSI bus must be correctly terminated at the end of the bus. Most Sun  
devices use auto-termination. See the documentation that came with the device.  
This host adapter has active terminators with an automatic means of enabling and  
disabling the termination. All the termination circuit derives its power from the  
PCI or SCSI bus. When the PCI bus power is removed, active SCSI termination is  
maintained if the other SCSI device supplies power to the Term Pwr pins of the  
SCSI bus.  
Appendix A  
Ultra320 SCSI Configuration  
15  
 
     
SCSI Symbols  
One of the four following symbols is placed near a SCSI port to indicate which type  
of SCSI the port is using. The icon may appear alone or with descriptive text.  
SE  
LVD  
LVD/MSE  
HVD  
Acronym  
Meaning  
SE  
single-ended  
LVD  
MSE  
HVD  
low-voltage differential  
multi-mode single ended  
high-voltage differential  
16 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
 
APPENDIX  
B
Specifications  
The chapter contains the specifications for the low-voltage differential (LVD) Sun  
StorEdge PCI/PCI-X Dual Ultra320 SCSI host adapter.  
The following topics are discussed:  
Physical Dimensions  
TABLE B-1 Physical Dimensions  
Dimension  
Measurement  
Board Without Bracket  
Board With Bracket  
Length  
Width  
Height  
Weight  
7.3 inches (185 meters)  
6.9 inches  
(175 millimeters)  
5.0 inches  
(127 millimeters)  
4.2 inches  
(107 millimeters)  
.85 inches  
(21.6 millimeters)  
.5 inches  
(12.7 millimeters)  
6.0 oz (43.42 g)  
N/A  
17  
 
     
Power Requirements  
TABLE B-2 Power Requirements  
Voltage  
Maximum Current  
5V 5%  
3.3V 9%  
12V 5%  
3A  
0.0A  
0.0A  
Performance Specifications  
TABLE B-3 Performance Specifications  
Feature  
Specification  
PCI/PCI-X bus clock frequency  
PCI data burst rate  
33 MHz, 66 MHz, and 133 MHz  
*
264 MBps @33 MHz,  
528 MBps @66 MHz,  
1064 MBps @133 MHz  
SCSI synchronous max imum transfer rate  
PCI data/address lines  
PCI modes  
320 MBps (wide)  
AD63-0  
Master/slave  
SCSI interface  
Low-voltage differential  
SCSI bus parity  
Yes  
Yes  
Yes  
Yes  
SCSI cyclic redundancy check (CRC)  
SCSI 8-bit bus devices  
SCSI 16-bit bus devices  
*
MBps = megabytes per second  
18 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
   
PCI Edge Connector Pin Definitions  
TABLE B-4 PCI Edge Connector Pin Definitions J1B (Top)  
Pin  
1
Description  
-12V  
Pin  
Description  
Pin  
Description  
Pin  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
Description  
GND  
25 +3.3V  
26 C_BE3  
27 AD23  
28 GND  
29 AD21  
30 AD19  
31 +3.3V  
49 GND  
50 KEYWAY  
51 KEYWAY  
52 AD08  
53 AD07  
54 +3.3V  
55 AD05  
56 AD03  
57 GND  
58 AD01  
59 3V/5V  
60 ACK64  
61 +5V  
2
AD[55]  
AD[53]  
GND  
TCK  
3
GND  
4
TDO  
5
AD[51]  
AD[49]  
+5V/+3.3V  
AD[47]  
AD[45]  
GND  
+5V  
6
+5V  
7
INTB  
AD17  
8
INTD  
32  
9
GND (PRSNT1)  
RESERVED  
GND (PRSNT2)  
KEYWAY  
KEYWAY  
RESERVED  
GND  
33 C_BE2  
34 GND  
35 IRDY  
36 +3.3V  
37 DEVSEL  
38 GND  
39 LOCK  
40 PERR  
41 +3.3V  
42 SERR  
43 +3.3V  
44 C_BE1  
45 AD14  
46 GND  
47 AD12  
48 AD10  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
AD[43]  
AD[41]  
GND  
AD[39]  
AD[37]  
+5V/+3.3V  
AD[35]  
AD[33]  
GND  
62 +5V  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
RESERVED  
GND  
CLK  
C/BE[6]#  
C/BE[4]#  
GND  
GND  
REQ  
3V/5V  
AD31  
AD[63]  
RESERVED  
RESERVED  
AD[61]  
AD29  
+5V/+3.3V  
AD[59]  
22 GND  
23 AD27  
24 AD25  
94 GND  
AD[57]  
Appendix B  
 
Specifications  
19  
 
TABLE B-5 PCI Edge Connector Pin Definitions J1A (Bottom)  
Pin  
1
Description  
TRST  
Pin  
Description  
Pin  
Description  
Pin  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
Description  
AD[56]  
AD[54]  
+5V/+3.3V  
AD[52]  
AD[50]  
GND  
25 AD24  
26 IDSEL  
27 +3.3V  
28 AD22  
29 AD20  
30 GND  
31 AD18  
49 AD09  
50 KEYWAY  
51 KEYWAY  
52 C_BE0  
53 +3.3V  
54 AD06  
55 AD04  
56 GND  
57 AD02  
58 AD00  
59 3V/5V  
60 REQ64  
61 +5V  
2
+12V  
3
TMS  
4
TDI  
5
+5V  
6
INTA  
7
AD[48]  
AD[46]  
GND  
INTC  
8
AD16  
+5V  
32  
9
RESERVED  
3V/5V  
RESERVED  
KEYWAY  
KEYWAY  
RESERVED  
RST  
33 +3.3V  
34 FRAME  
35 GND  
36 TRDY  
37 GND  
38 STOP  
39 +3.3V  
40 SDONE  
41 SBO  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
AD[44]  
AD[42]  
+5V/+3.3V  
AD[40]  
AD[38]  
GND  
62 +5V  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
GND  
C/BE[7]#  
C/BE[5]#  
+5V/+3.3V  
PAR64  
AD[36]  
AD[34]  
GND  
3V/5V  
GNT  
GND  
42 GND  
43 PAR  
AD[32]  
RESERVED  
GND  
RESERVED  
AD30  
AD[62]  
GND  
44 AD15  
45 +3.3V  
46 AD13  
47 AD11  
48 GND  
+3.3V  
AD[60]  
AD[58]  
GND  
22 AD28  
23 AD26  
24 GND  
RESERVED  
20 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
SCSI Connector Pin Definitions  
34  
68  
1
35  
VHDCI Connector  
34  
68  
1
35  
Internal SCSI Connector  
FIGURE B-1 VHDCI and Internal SCSI Connectors  
TABLE B-6 SCSI Connector Pin Definitions  
Pin  
1
Description  
+SD(12)  
+SD(13)  
+SD(14)  
+SD(15)  
+SDP(1)  
GND  
Pin  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
Description  
+RST  
Pin  
Description  
SD(6)-  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
2
+MSG  
+SEL  
SD(7)-  
3
SDP-  
4
+C/D  
Cable Sense (GND)  
TERMPWR  
TERMPWR  
OPEN  
5
+REQ  
6
+I/O  
7
+SD(0)  
GND  
8
+SD(1)  
+SD(8)  
+SD(9)  
+SD(10)  
+SD(11)  
SD(12)-  
SD(13)-  
SD(14)-  
SP(15)-  
SDP(1)-  
GND  
ATN-  
9
+SD(2)  
GND  
10  
11  
12  
13  
14  
15  
16  
17  
+SD(3)  
BSY-  
+SD(4)  
ACK-  
+SD(5)  
RST-  
+SD(6)  
MSG-  
+SD(7)  
SEL-  
+SDP  
C/D-  
DIFFSENS  
TERMPWR  
REQ-  
I/O-  
Appendix B  
 
Specifications  
21  
 
TABLE B-6 SCSI Connector Pin Definitions (Continued)  
Pin  
18  
19  
20  
21  
22  
23  
Description  
TERMPWR  
OPEN  
Pin  
41  
42  
43  
44  
45  
46  
Description  
SD(0)-  
SD(1)-  
SD(2)-  
SD(3)-  
SD(4)-  
SD(5)-  
Pin  
64  
65  
66  
67  
68  
Description  
GND  
SD(8)-  
+ATN  
SD(9)-  
GND  
SD(10)-  
SD(11)-  
+BSY  
+ACK  
22 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
APPENDIX  
C
Declaration of Conformity,  
Regulatory Compliance, and Safety  
Statements  
This appendix contains the following information that applies to the Sun StorEdge  
PCI/PCI-X Dual Ultra320 SCSI host adapter:  
23  
 
   
Declaration of Conformity  
Compliance Model Number:  
Product Family Name:  
LSI22320-SR  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter (SGXPCI2SCSILM320-Z)  
EMC  
USA - FCC Class B  
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
1. This equipment may not cause harmful interference.  
2. This equipment must accept any interference that may cause undesired operation.  
European Union  
This equipment complies with the following requirements of the EMC Directive 89/336/EEC:  
As Telecommunication Network Equipment (TNE) in Both Telecom Centers and Other Than Telecom Centers per (as applicable):  
EN300-386 V.1.3.2 (2003-05) Required Limits:  
EN 55022:1994 +A1:1995 +A2:1997 Class B  
EN 61000-3-2:2000  
EN 61000-3-3:1995 +A1:2000  
IEC 61000-4-2  
Pass  
Pass  
6 kV (Direct), 8 kV (Air)  
IEC 61000-4-3  
3 V/m 80-1000MHz, 10 V/m 800-960 MHz, and 1400-2000 MHz  
IEC 61000-4-4  
1 kV AC and DC Power Lines, 0.5 kV Signal Lines  
IEC 61000-4-5  
2 kV AC Line-Gnd, 1 kV AC Line-Line and Outdoor Signal Lines, 0.5 kV Indoor signal Lines > 10m  
IEC 61000-4-6  
3 V  
IEC 61000-4-11  
Pass  
As Information Technology Equipment (ITE) Class B per (as applicable):  
EN55022:1994 +A1 1995 +A2:1997 Class B  
EN 61000-3-2:2000  
EN 61000-3-3:1995 +A1:2000  
Pass  
Pass  
EN 55024:1998 +A1: 2001 +A2:2003 Required Limits:  
IEC 61000-4-2  
IEC 61000-4-3  
IEC 61000-4-4  
IEC 61000-4-5  
IEC 61000-4-6  
IEC 61000-4-8  
IEC 61000-4-11  
4 kV (Direct), 8 kV (Air)  
3 V/m  
1 kV AC Power Lines, 0.5 kV Signal and DC Power Lines  
1 kV AC Line-Line and Outdoor Signal Lines, 2 kV AC Line-Gnd, 0.5 kV DC Power Lines  
3 V  
1 A/m  
Pass  
Safety: This equipment complies with the following requirements of the Low Voltage Directive 73/23/EEC:  
EC Type Examination Certificates:  
EN60950-1:2001, First Edition  
IEC 60950-1:2001, 1st Edition  
TÜV Rheinland Certificate No.  
CB Scheme Certificate No.  
Evaluated to all CB Countries  
UL 60950:2000, 3rd Edition, CSA C22.2 No. 60950-00  
File:  
Supplementary Information: This equipment was tested and complies with all the requirements for the CE Mark.  
This equipment complies with the Restriction of Hazardous Substances (RoHS) directive  
2002/95/EC.  
/S/  
/S/  
Dennis P. Symanski  
DATE  
Donald Cameron  
DATE  
Worldwide Compliance Office  
Sun Microsystems, Inc.  
4150 Network Circle, MPK15-102  
Santa Clara, CA 95054, U.S.A.  
Tel: 650-786-3255  
Program Manager/Quality Systems  
Sun Microsystems Scotland, Limited  
Blackness Road, Phase I, Main Bldg.  
Springfield, EH49 7LR  
Scotland, United Kingdom  
Tel: +44 1 506 672 539  
Fax: +44 1 506 670 011  
Fax: 650-786-3723  
24 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
 
Appendix C  
Declaration of Conformity  
25  
 
Regulatory Compliance Statements  
Your Sun product is marked to indicate its compliance class:  
Federal Communications Commission (FCC) — USA  
Department of Communications (DOC) — Canada  
Voluntary Control Council for Interference (VCCI) — Japan  
Please read the appropriate section that corresponds to the marking on your Sun product before attempting to install the  
product.  
FCC Class A Notice  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
1. This device may not cause harmful interference.  
2. This device must accept any interference received, including interference that may cause undesired operation.  
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment  
is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required  
to correct the interference at his own expense.  
Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to  
maintain compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded  
twisted-pair (UTP) cables.  
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the  
authority granted to the user by the FCC to operate this equipment.  
FCC Class B Notice  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
1. This device may not cause harmful interference.  
2. This device must accept any interference received, including interference that may cause undesired operation.  
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee  
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct  
the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/television technician for help.  
Shielded Cables: Connections between the workstation and peripherals must be made using shielded cables in order to  
maintain compliance with FCC radio frequency emission limits. Networking connections can be made using unshielded  
twisted pair (UTP) cables.  
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the  
authority granted to the user by the FCC to operate this equipment.  
26 Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
 
Depending on the type of power switch your device has,  
one of the following symbols may be used:  
Safety Agency Compliance  
Statements  
Read this section before beginning any procedure. The  
following text provides safety precautions to follow when  
installing a Sun Microsystems product.  
On – Applies AC power to the system.  
Off – Removes AC power from the system.  
Safety Precautions  
For your protection, observe the following safety  
precautions when setting up your equipment:  
Standby – The On/Standby switch is in the  
standby position.  
Follow all cautions and instructions marked on the  
equipment.  
Ensure that the voltage and frequency of your power  
source match the voltage and frequency inscribed on  
the equipment’s electrical rating label.  
Modifications to Equipment  
Do not make mechanical or electrical modifications to the  
equipment. Sun Microsystems is not responsible for  
regulatory compliance of a modified Sun product.  
Never push objects of any kind through openings in  
the equipment. Dangerous voltages may be present.  
Conductive foreign objects could produce a short  
circuit that could cause fire, electric shock, or damage  
to your equipment.  
Placement of a Sun Product  
Caution – Do not block or cover the  
openings of your Sun product. Never place a  
Sun product near a radiator or heat register.  
Failure to follow these guidelines can cause  
overheating and affect the reliability of your  
Sun product.  
Symbols  
The following symbols may appear in this book:  
Caution – There is a risk of personal injury  
and equipment damage. Follow the  
instructions.  
Noise Level  
In compliance with the requirements defined in DIN 45635  
Part 1000, the workplace-dependent noise level of this  
product is less than 70 db(A).  
Caution – Hot surface. Avoid contact.  
Surfaces are hot and may cause personal  
injury if touched.  
Caution – Hazardous voltages are present.  
To reduce the risk of electric shock and danger  
to personal health, follow the instructions.  
Appendix C Declaration of Conformity, Regulatory, and Safety Information  
 
27  
   
The following caution applies only to devices with multiple  
power cords:  
SELV Compliance  
Safety status of I/O connections comply to SELV  
requirements.  
Caution – For products with multiple  
power cords, all power cords must be  
disconnected to completely remove power  
from the system.  
Power Cord Connection  
Caution – Sun products are designed to  
work with power systems having a grounded  
neutral (grounded return for DC-powered  
products). To reduce the risk of electric shock,  
do not plug Sun products into any other type  
of power system. Contact your facilities  
manager or a qualified electrician if you are  
not sure what type of power is supplied to  
your building.  
Battery Warning  
Caution – There is danger of explosion if  
batteries are mishandled or incorrectly  
replaced. On systems with replaceable  
batteries, replace only with the same  
manufacturer and type or equivalent type  
recommended by the manufacturer per the  
instructions provided in the product service  
manual. Do not disassemble batteries or  
attempt to recharge them outside the system.  
Do not dispose of batteries in fire. Dispose of  
batteries properly in accordance with the  
manufacturer’s instructions and local  
regulations. Note that on Sun CPU boards,  
there is a lithium battery molded into the real-  
time clock. These batteries are not customer  
replaceable parts.  
Caution – Not all power cords have the  
same current ratings. Do not use the power  
cord provided with your equipment for any  
other products or use. Household extension  
cords do not have overload protection and are  
not meant for use with computer systems. Do  
not use household extension cords with your  
Sun product.  
System Unit Cover  
You must remove the cover of your Sun computer system  
unit to add cards, memory, or internal storage devices. Be  
sure to replace the cover before powering on your computer  
system.  
The following caution applies only to devices with a  
Standby power switch:  
Caution – Do not operate Sun products  
without the cover in place. Failure to take this  
precaution may result in personal injury and  
system damage.  
Caution – The power switch of this product  
functions as a standby type device only. The  
power cord serves as the primary disconnect  
device for the system. Be sure to plug the  
power cord into a grounded power outlet that  
is nearby the system and is readily accessible.  
Do not connect the power cord when the  
power supply has been removed from the  
system chassis.  
28  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
Rack System Warning  
CD and DVD Devices  
The following warnings apply to Racks and Rack Mounted  
The following caution applies to CD, DVD, and other  
systems.  
optical devices.  
Caution – For safety, equipment should  
always be loaded from the bottom up. That is,  
install the equipment that will be mounted in  
the lowest part of the rack first, then the next  
higher systems, etc.  
Caution – Use of controls, adjustments, or  
the performance of procedures other than  
those specified herein may result in hazardous  
radiation exposure.  
Conformité aux normes de sécurité  
Caution – To prevent the rack from tipping  
during equipment installation, the anti-tilt bar  
on the rack must be deployed.  
Veuillez lire attentivement cette section avant de  
commencer. Ce texte traite des mesures de sécurité qu’il  
convient de prendre pour l’installation d’un produit Sun  
Microsystems.  
Caution – To prevent extreme operating  
temperature within the rack insure that the  
maximum temperature does not exceed the  
product’s ambient rated temperatures.  
Mesures de sécurité  
Pour votre sécurité, nous vous recommandons de suivre  
scrupuleusement les mesures de sécurité ci-dessous lorsque  
vous installez votre matériel:  
Suivez tous les avertissements et toutes les  
instructions inscrites sur le matériel.  
Caution – To prevent extreme operating  
temperatures due to reduced airflow  
consideration should be made to the amount  
of air flow that is required for a safe operation  
of the equipment.  
Assurez-vous que la tension et la fréquence de votre  
source d'alimentation correspondent à la tension et à  
la fréquence indiquées sur l'étiquette de la tension  
électrique nominale du matériel  
N'introduisez jamais d'objets quels qu'ils soient dans  
les ouvertures de l'équipement. Vous pourriez vous  
trouver en présence de hautes tensions dangereuses.  
Tout objet étranger conducteur risque de produire un  
court-circuit pouvant présenter un risque d'incendie  
ou de décharge électrique, ou susceptible  
Laser Compliance Notice  
Sun products that use laser technology comply with Class 1  
laser requirements.  
d'endommager le matériel.  
Symboles  
Class 1 Laser Product  
Luokan 1 Laserlaite  
Klasse 1 Laser Apparat  
Laser Klasse 1  
Vous trouverez ci-dessous la signification des différents  
symboles utilisés:  
Attention – Vous risquez d'endommager le  
matériel ou de vous blesser. Veuillez suivre les  
instructions.  
Attention – Surfaces brûlantes. Evitez tout  
contact. Les surfaces sont brûlantes. Vous  
risquez de vous blesser si vous les touchez.  
Appendix C Declaration of Conformity, Regulatory, and Safety Information  
 
29  
Connexion du cordon d’alimentation  
Attention – Tensions dangereuses. Pour  
réduire les risques de décharge électrique et  
de danger physique, observez les consignes  
indiquées.  
Attention – Les produits Sun sont conçus  
pour fonctionner avec des systèmes  
d'alimentation équipés d'un conducteur  
neutre relié à la terre (conducteur neutre pour  
produits alimentés en CC). Pour réduire les  
risques de décharge électrique, ne branchez  
jamais les produits Sun sur une source  
d'alimentation d'un autre type. Contactez le  
gérant de votre bâtiment ou un électricien  
agréé si vous avez le moindre doute quant au  
type d'alimentation fourni dans votre  
bâtiment.  
Selon le type d'interrupteur marche/arrêt dont votre  
appareil est équipé, l'un des symboles suivants sera utilisé:  
Marche – Met le système sous tension  
alternative.  
Arret – Met le système hors tension  
alternative.  
Attention – Tous les cordons d'alimentation  
ne présentent pas les mêmes caractéristiques  
électriques. Les cordons d'alimentation à  
usage domestique ne sont pas protégés contre  
les surtensions et ne sont pas conçus pour être  
utilisés avec des ordinateurs. N'utilisez jamais  
de cordon d'alimentation à usage domestique  
avec les produits Sun.  
Veilleuse – L'interrupteur Marche/Veille  
est sur la position de veille.  
Modification du matériel  
N'apportez aucune modification mécanique ou électrique  
au matériel. Sun Microsystems décline toute responsabilité  
quant à la non-conformité éventuelle d'un produit Sun  
modifié.  
L'avertissement suivant s'applique uniquement aux  
systèmes équipés d'un interrupteur Veille:  
Attention – L'interrupteur d'alimentation  
de ce produit fonctionne uniquement comme  
un dispositif de mise en veille. Le cordon  
d'alimentation constitue le moyen principal de  
déconnexion de l'alimentation pour le  
système. Assurez-vous de le brancher dans  
une prise d'alimentation mise à la terre près  
du système et facile d'accès. Ne le branchez  
pas lorsque l'alimentation électrique ne se  
trouve pas dans le châssis du système.  
Positionnement d’un produit Sun  
Attention – Evitez d'obstruer ou de  
recouvrir les orifices de votre produit Sun.  
N'installez jamais un produit Sun près d'un  
radiateur ou d'une source de chaleur. Si vous  
ne respectez pas ces consignes, votre produit  
Sun risque de surchauffer et son  
fonctionnement en sera altéré.  
L'avertissement suivant s'applique uniquement aux  
systèmes équipés de plusieurs cordons d'alimentation:  
Niveau de pression acoustique  
Le niveau de pression acoustique du lieu de travail définie  
par la norme DIN 45 635 Part 1000 doit être au maximum de  
70 db(A).  
Attention – Pour mettre un système équipé  
de plusieurs cordons d'alimentation hors  
tension, il est nécessaire de débrancher tous  
les cordons d'alimentation.  
Conformité SELV  
Le niveau de sécurité des connexions E/S est conforme aux  
normes SELV.  
30  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
Mise en garde relative aux batteries  
Attention – Afin d'éviter que le rack ne  
penche pendant l'installation du matériel, tirez  
la barre anti-basculement du rack.  
Attention – Les batteries risquent  
d’exploser en cas de manipulation maladroite  
ou de remplacement incorrect. Pour les  
systèmes dont les batteries sont remplaçables,  
effectuez les remplacements uniquement selon  
le modèle du fabricant ou un modèle  
Attention – Pour éviter des températures de  
fonctionnement extrêmes dans le rack,  
assurez-vous que la température maximale ne  
dépasse pas la fourchette de températures  
ambiantes du produit déterminée par le  
fabricant.  
équivalent recommandé par le fabricant,  
conformément aux instructions fournies dans  
le manuel de service du système. N’essayez en  
aucun cas de démonter les batteries, ni de les  
recharger hors du système. Ne les jetez pas au  
feu. Mettez-les au rebut selon les instructions  
du fabricant et conformément à la législation  
locale en vigueur. Notez que sur les cartes  
processeur de Sun, une batterie au lithium a  
été moulée dans l'horloge temps réel. Les  
batteries ne sont pas des pièces remplaçables  
par le client.  
Attention – Afin d'empêcher des  
températures de fonctionnement extrêmes  
provoquées par une aération insuffisante,  
assurez-vous de fournir une aération  
appropriée pour un fonctionnement du  
matériel en toute sécurité  
Couvercle de l'unité  
Avis de conformité des appareils laser  
Les produits Sun qui font appel aux technologies lasers sont  
conformes aux normes de la classe 1 en la matière.  
Pour ajouter des cartes, de la mémoire ou des périphériques  
de stockage internes, vous devez retirer le couvercle de  
votre système Sun. Remettez le couvercle supérieur en  
place avant de mettre votre système sous tension.  
Attention – Ne mettez jamais des produits  
Sun sous tension si leur couvercle supérieur  
n'est pas mis en place. Si vous ne prenez pas  
ces précautions, vous risquez de vous blesser  
ou d'endommager le système.  
Class 1 Laser Product  
Luokan 1 Laserlaite  
Klasse 1 Laser Apparat  
Laser Klasse 1  
Mise en garde relative au système en rack  
La mise en garde suivante s'applique aux racks et aux  
systèmes montés en rack.  
Périphériques CD et DVD  
L'avertissement suivant s'applique aux périphériques CD,  
DVD et autres périphériques optiques:  
Attention – Pour des raisons de sécurité, le  
matériel doit toujours être chargé du bas vers  
le haut. En d'autres termes, vous devez  
installer, en premier, le matériel qui doit se  
trouver dans la partie la plus inférieure du  
rack, puis installer le matériel sur le niveau  
suivant, etc.  
Attention – L'utilisation de contrôles et de  
réglages ou l'application de procédures autres  
que ceux spécifiés dans le présent document  
peuvent entraîner une exposition à des  
radiations dangereuses.  
Appendix C Declaration of Conformity, Regulatory, and Safety Information  
 
31  
Je nach Netzschaltertyp an Ihrem Gerät kann eines der  
folgenden Symbole verwendet werden:  
Einhaltung sicherheitsbehördlicher  
Vorschriften  
Lesen Sie vor dem Ausführen von Arbeiten diesen  
Abschnitt. Im folgenden Text werden Sicherheitsvor-  
kehrungen beschrieben, die Sie bei der Installation eines  
Sun Microsystems-Produkts beachten müssen.  
Ein – Versorgt das System mit Wechselstrom.  
Aus– Unterbricht die Wechselstromzufuhr  
zum Gerät.  
Sicherheitsvorkehrungen  
Treffen Sie zu Ihrem eigenen Schutz bei der Installation des  
Geräts die folgenden Sicherheitsvorkehrungen:  
Wartezustand – Der Ein-/Standby-Netz-  
Beachten Sie alle auf den Geräten angebrachten  
Warnhinweise und Anweisungen.  
schalter befindet sich in der Standby-Position.  
Stellen Sie sicher, dass Spannung und Frequenz der  
Stromversorgung den Nennleistungen auf dem am  
Gerät angebrachten Etikett entsprechen.  
Modifikationen des Geräts  
Nehmen Sie keine elektrischen oder mechanischen  
Gerätemodifikationen vor. Sun Microsystems ist für die  
Einhaltung der Sicherheitsvorschriften von modifizierten  
Sun-Produkten nicht haftbar.  
Führen Sie niemals Fremdobjekte in die Öffnungen  
am Gerät ein. Es können gefährliche Spannungen  
anliegen. Leitfähige Fremdobjekte können einen  
Kurzschluss verursachen, der einen Brand, Strom-  
schlag oder Geräteschaden herbeiführen kann.  
Aufstellung von Sun-Geräten  
Symbole  
Die Symbole in diesem Handbuch haben folgende  
Bedeutung:  
Achtung – Geräteöffnungen Ihres Sun-  
Produkts dürfen nicht blockiert oder  
abgedeckt werden. Sun-Geräte sollten niemals  
in der Nähe von Heizkörpern oder Heißluft-  
klappen aufgestellt werden. Die Nichtbeach-  
tung dieser Richtlinien kann Überhitzung  
verursachen und die Zuverlässigkeit Ihres  
Sun-Geräts beeinträchtigen.  
Achtung – Gefahr von Verletzung und  
Geräteschaden. Befolgen Sie die Anwei-  
sungen.  
Achtung – Heiße Oberfläche. Nicht  
berühren, da Verletzungsgefahr durch heiße  
Oberfläche besteht.  
Lautstärke  
Gemäß den in DIN 45 635 Teil 1000 definierten Vorschriften  
beträgt die arbeitsplatzbedingte Lautstärke dieses Produkts  
weniger als 70 dB(A).  
Achtung – Gefährliche Spannungen.  
Befolgen Sie die Anweisungen, um  
Stromschläge und Verletzungen zu vermeiden.  
SELV-Konformität  
Der Sicherheitsstatus der E/A-Verbindungen entspricht  
den SELV-Anforderungen.  
32  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
Anschluss des Netzkabels  
Warnung bezüglich Batterien  
Achtung – Sun-Geräte sind für  
Achtung – Bei unsachgemäßer  
Handhabung oder nicht fachgerechtem  
Austausch der Batterien besteht  
Stromversorgungssysteme mit einem  
geerdeten neutralen Leiter (geerdeter  
Rückleiter bei gleichstrombetriebenen  
Geräten) ausgelegt. Um die Gefahr von  
Stromschlägen zu vermeiden, schließen Sie  
das Gerät niemals an andere Stromversor-  
gungssysteme an. Wenden Sie sich an den  
zuständigen Gebäudeverwalter oder an einen  
qualifizierten Elektriker, wenn Sie nicht sicher  
wissen, an welche Art von Stromversor-  
gungssystem Ihr Gebäude angeschlossen ist.  
Explosionsgefahr. Verwen-den Sie bei  
Systemen mit austauschbaren Batterien  
ausschließlich Ersatzbatterien desselben Typs  
und Herstellers bzw. einen entsprechenden,  
vom Hersteller gemäß den Anweisungen im  
Service-Handbuch des Produkts empfohlenen  
Batterietyp. Versuchen Sie nicht, die Batterien  
auszubauen oder außerhalb des Systems  
wiederaufzuladen. Werfen Sie die Batterien  
nicht ins Feuer. Entsorgen Sie die Batterien  
entsprechend den Anweisungen des  
Herstellers und den vor Ort geltenden  
Vorschriften. CPU-Karten von Sun verfügen  
über eine Echtzeituhr mit integrier-ter  
Lithiumbatterie. Diese Batterie darf nur von  
einem qualifizierten Servicetechniker aus-  
gewechselt werden.  
Achtung – Nicht alle Netzkabel verfügen  
über die gleichen Nennwerte. Herkömmliche,  
im Haushalt verwendete Verlängerungskabel  
besitzen keinen Überlastschutz und sind  
daher für Computersysteme nicht geeignet.  
Verwenden Sie bei Ihrem Sun-Produkt keine  
Haushalts-Verlängerungskabel.  
Gehäuseabdeckung  
Die folgende Warnung gilt nur für Geräte mit Standby-  
Netzschalter:  
Sie müssen die Abdeckung Ihres Sun-Computersystems  
entfernen, um Karten, Speicher oder interne Speichergeräte  
hinzuzufügen. Bringen Sie vor dem Einschalten des  
Systems die Gehäuseabdeckung wieder an.  
Achtung – Beim Netzschalter dieses Geräts  
handelt es sich nur um einen Ein/Standby-  
Schalter. Zum völligen Abtrennen des Systems  
von der Stromversorgung dient hauptsächlich  
das Netzkabel. Stellen Sie sicher, dass das  
Netzkabel an eine frei zugängliche geerdete  
Steckdose in der Nähe des Systems ange-  
schlossen ist. Schließen Sie das Stromkabel  
nicht an, wenn die Stromversorgung vom  
Systemchassis entfernt wurde.  
Achtung – Nehmen Sie Sun-Geräte nicht  
ohne Abdeckung in Betrieb. Die  
Nichtbeachtung dieses Warnhinweises kann  
Verletzungen oder Geräteschaden zur Folge  
haben.  
Warnungen bezüglich in Racks eingebauter  
Systeme  
Die folgenden Warnungen gelten für Racks und in Racks  
Die folgende Warnung gilt nur für Geräte mit mehreren  
Netzkabeln:  
eingebaute Systeme:  
Achtung – Bei Produkten mit mehreren  
Netz-kabeln müssen alle Netzkabel abgetrennt  
wer-den, um das System völlig von der  
Stromver-sorgung zu trennen.  
Achtung – Aus Sicherheitsgründen sollten  
sämtliche Geräte von unten nach oben in  
Racks eingebaut werden. Installieren Sie also  
zuerst die Geräte, die an der untersten  
Appendix C Declaration of Conformity, Regulatory, and Safety Information  
 
33  
Position im Rack eingebaut werden, gefolgt  
von den Systemen, die an nächsthöherer Stelle  
eingebaut werden, usw.  
Normativas de seguridad  
Lea esta sección antes de realizar cualquier operación. En  
ella se explican las medidas de seguridad que debe tomar al  
instalar un producto de Sun Microsystems.  
Achtung – Verwenden Sie beim Einbau den  
Kippschutz am Rack, um ein Umkippen zu  
vermeiden.  
Medidas de seguridad  
Para su protección, tome las medidas de seguridad  
siguientes durante la instalación del equipo:  
Siga todos los avisos e instrucciones indicados en el  
equipo.  
Achtung – Um extreme  
Betriebstemperaturen im Rack zu vermeiden,  
stellen Sie sicher, dass die Maximaltemperatur  
die Nennleistung der Umgebungstemperatur  
für das Produkt nicht überschreitet  
Asegúrese de que el voltaje y frecuencia de la fuente  
de alimentación coincidan con el voltaje y frecuencia  
indicados en la etiqueta de clasificación eléctrica del  
equipo.  
No introduzca objetos de ningún tipo por las rejillas  
del equipo, ya que puede quedar expuesto a voltajes  
peligrosos. Los objetos conductores extraños pueden  
producir cortocircuitos y, en consecuencia, incendios,  
descargas eléctricas o daños en el equipo.  
Achtung – Um extreme  
Betriebstemperaturen durch verringerte  
Luftzirkulation zu vermei-den, sollte die für  
den sicheren Betrieb des Geräts erforderliche  
Luftzirkulation eingesetzt werden.  
Símbolos  
En este documento aparecen los siguientes símbolos:  
Precaución – Existe el riesgo de que se  
produzcan lesiones personales y daños en el  
equipo. Siga las instrucciones.  
Hinweis zur Laser-Konformität  
Sun-Produkte, die die Laser-Technologie verwenden,  
entsprechen den Laser-Anforderungen der Klasse 1.  
Precaución – Superficie caliente. Evite  
todo contacto. Las superficies están calientes y  
pueden causar lesiones personales si se tocan.  
Class 1 Laser Product  
Luokan 1 Laserlaite  
Klasse 1 Laser Apparat  
Laser Klasse 1  
Precaución – Voltaje peligroso. Para  
reducir el riesgo de descargas eléctricas y  
lesiones personales, siga las instrucciones.  
CD- und DVD-Geräte  
Die folgende Warnung gilt für CD-, DVD- und andere  
optische Geräte:  
Achtung – Die hier nicht aufgeführte  
Verwendung von Steuerelementen,  
Anpassungen oder Ausführung von  
Vorgängen kann eine gefährliche  
Strahlenbelastung verursachen.  
34  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
En función del tipo de interruptor de alimentación del que  
disponga el dispositivo, se utilizará uno de los símbolos  
siguientes:  
Conexión del cable de alimentación  
Precaución – Los productos Sun se han  
diseñado para funcionar con sistemas de  
alimentación que cuenten con un conductor  
neutro a tierra (con conexión a tierra de  
regreso para los productos con alimentación  
de CC). Para reducir el riesgo de descargas  
eléctricas, no conecte ningún producto Sun a  
otro tipo de sistema de alimentación. Póngase  
en contacto con el encargado de las  
Encendido – Suministra alimentación de  
CA al sistema.  
Apagado – Corta la alimentación de CA del  
sistema.  
instalaciones de su empresa o con un  
electricista cualificado en caso de que no esté  
seguro del tipo de alimentación del que se  
dispone en el edificio.  
Espera – El interruptor de  
encendido/espera está en la posición de  
espera.  
Precaución – No todos los cables de  
alimentación tienen la misma clasificación  
eléctrica. Los alargadores de uso doméstico no  
cuentan con protección frente a sobrecargas y  
no están diseñados para su utilización con  
sistemas informáticos. No utilice alargadores  
de uso doméstico con el producto Sun.  
Modificaciones en el equipo  
No realice modificaciones de tipo mecánico ni eléctrico en el  
equipo. Sun Microsystems no se hace responsable del  
cumplimiento de normativas en caso de que un producto  
Sun se haya modificado.  
Colocación de un producto Sun  
La siguiente medida solamente se aplica a aquellos  
dispositivos que dispongan de un interruptor de  
alimentación de espera:  
Precaución – No obstruya ni tape las  
rejillas del producto Sun. Nunca coloque un  
producto Sun cerca de radiadores ni fuentes  
de calor. Si no sigue estas indicaciones, el  
producto Sun podría sobrecalentarse y la  
fiabilidad de su funcionamiento se vería  
afectada.  
Precaución – El interruptor de  
alimentación de este producto funciona  
solamente como un dispositivo de espera. El  
cable de alimentación hace las veces de  
dispositivo de desconexión principal del  
sistema. Asegúrese de que conecta el cable de  
alimentación a una toma de tierra situada  
cerca del sistema y de fácil acceso. No conecte  
el cable de alimentación si la unidad de  
alimentación no se encuentra en el bastidor  
del sistema.  
Nivel de ruido  
De conformidad con los requisitos establecidos en el  
apartado 1000 de la norma DIN 45635, el nivel de ruido en  
el lugar de trabajo producido por este producto es menor de  
70 db(A).  
Cumplimiento de la normativa para  
instalaciones SELV  
Las condiciones de seguridad de las conexiones de entrada  
y salida cumplen los requisitos para instalaciones SELV (del  
inglés Safe Extra Low Voltage, voltaje bajo y seguro).  
Appendix C Declaration of Conformity, Regulatory, and Safety Information  
 
35  
La siguiente medida solamente se aplica a aquellos  
dispositivos que dispongan de varios cables de  
alimentación:  
Advertencia sobre el sistema en bastidor  
Las advertencias siguientes se aplican a los sistemas  
montados en bastidor y a los propios bastidores.  
Precaución – En los productos que  
cuentan con varios cables de alimentación,  
debe desconectar todos los cables de  
alimentación para cortar por completo la  
alimentación eléctrica del sistema.  
Precaución – Por seguridad, siempre  
deben montarse los equipos de abajo arriba. A  
saber, primero debe instalarse el equipo que se  
situará en el bastidor inferior; a continuación,  
el que se situará en el siguiente nivel, etc.  
Advertencia sobre las baterías  
Precaución – Para evitar que el bastidor se  
vuelque durante la instalación del equipo,  
debe extenderse la barra antivolcado del  
bastidor.  
Precaución – Si las baterías no se  
manipulan o reemplazan correctamente, se  
corre el riesgo de que estallen. En los sistemas  
que cuentan con baterías reemplazables,  
reemplácelas sólo con baterías del mismo  
fabricante y el mismo tipo, o un tipo  
Precaución – Para evitar que se alcance  
una temperatura de funcionamiento extrema  
en el bastidor, asegúrese de que la  
temperatura máxima no sea superior a la  
temperatura ambiente establecida como  
adecuada para el producto.  
equivalente recomendado por el fabricante, de  
acuerdo con las instrucciones descritas en el  
manual de servicio del producto. No  
desmonte las baterías ni intente recargarlas  
fuera del sistema. No intente deshacerse de las  
baterías echándolas al fuego. Deshágase de las  
baterías correctamente de acuerdo con las  
instrucciones del fabricante y las normas  
locales. Tenga en cuenta que en las placas CPU  
de Sun, hay una batería de litio incorporada  
en el reloj en tiempo real. Los usuarios no  
deben reemplazar este tipo de baterías.  
Precaución – Para evitar que se alcance  
una temperatura de funcionamiento extrema  
debido a una circulación de aire reducida,  
debe considerarse la magnitud de la  
circulación de aire requerida para que el  
equipo funcione de forma segura.  
Cubierta de la unidad del sistema  
Aviso de cumplimiento de la normativa para  
la utilización de láser  
Los productos Sun que utilizan tecnología láser cumplen los  
Debe extraer la cubierta de la unidad del sistema  
informático Sun para instalar tarjetas, memoria o  
dispositivos de almacenamiento internos. Vuelva a colocar  
la cubierta antes de encender el sistema informático.  
requisitos establecidos para los productos láser de clase 1.  
Precaución – No ponga en funcionamiento  
los productos Sun que no tengan colocada la  
cubierta. De lo contrario, puede sufrir lesiones  
personales y ocasionar daños en el sistema.  
Class 1 Laser Product  
Luokan 1 Laserlaite  
Klasse 1 Laser Apparat  
Laser Klasse 1  
36  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 
Dispositivos de CD y DVD  
La siguiente medida se aplica a los dispositivos de CD y  
DVD, así como a otros dispositivos ópticos:  
Precaución – La utilización de controles,  
ajustes o procedimientos distintos a los aquí  
especificados puede dar lugar a niveles de  
radiación peligrosos.  
Nordic Lithium Battery Cautions  
Norge  
Advarsel – Litiumbatteri —  
Eksplosjonsfare. Ved utskifting benyttes kun  
batteri som anbefalt av apparatfabrikanten.  
Brukt batteri returneres apparatleverandøren.  
Sverige  
Varning – Explosionsfara vid felaktigt  
batteribyte. Använd samma batterityp eller en  
ekvivalent typ som rekommenderas av  
apparattillverkaren. Kassera använt batteri  
enligt fabrikantens instruktion.  
Danmark  
Advarsel! – Litiumbatteri —  
Eksplosionsfare ved fejlagtig håndtering.  
Udskiftning må kun ske med batteri af samme  
fabrikat og type. Levér det brugte batteri  
tilbage til leverandøren.  
Suomi  
Varoitus – Paristo voi räjähtää, jos se on  
virheellisesti asennettu. Vaihda paristo  
ainoastaan laitevalmistajan suosittelemaan  
tyyppiin. Hävitä käytetty paristo valmistajan  
ohjeiden mukaisesti.  
Appendix C Declaration of Conformity, Regulatory, and Safety Information  
 
37  
38  
Sun StorEdge PCI/PCI-X Dual Ultra320 SCSI Host Adapter Installation Guide • January 2007  
 

Sharp DVD Player XL DV60 User Manual
Snapper Lawn Mower Accessory 0 50576 User Manual
Sony Camera Lens 59 User Manual
Sony MP3 Player TCM 459V User Manual
Sony Stereo Receiver BKMFW50 User Manual
Sony Video Game Console SCPH 77007 User Manual
Spirit Fitness Equipment XE395 User Manual
Sterling Plumbing Outdoor Shower 71110112 User Manual
Sunbeam Cookware FP4500 User Manual
Superior Indoor Fireplace SDVPF N B User Manual